Dyno Graphs
#379
Eats, Sleeps, Dreams Rotary
Mod List:
Tuned by Dave at KDR on a Dynojet
11psi: 330.99rwhp and 277.06rwtq
13psi: 348.18rwhp and 315.94rwtq (84% injector duty cycle- room to work with if we wanted to get more out of it at the cost of reliability.)
- Stock Hitachi HT12 Sequential Twin Turbos
- Stock ported motor
- HKS Type S Front Mount Intercooler
- HKS Racing Suction Kit
- HKS 3" Downpipe
- Pettit Racing Resonated Midpipe
- HKS Carbon Ti 4.75" Exhaust
- HKS Circle Earth Kit (added a dyno proven 13rwhp)
- Unorthodox Racing SS Pulley Kit
- Efini Y-Pipe
- HKS Super Sequential Blow Off Valve
- RC 550cc Primary Injectors
- RC 1200cc Secondary Injectors
- Walbro 255lph Fuel Pump
- APEXi Power FC and Commander
- NGK BUR7EQP Leading Spark Plugs
- NGK BUR9EQP Trailing Spark Plugs
- Magnecor 8.5mm Ignition Wires
- Fluidyne Aluminum Race Radiator
- Pettit Racing Air Separator Tank
Tuned by Dave at KDR on a Dynojet
11psi: 330.99rwhp and 277.06rwtq
13psi: 348.18rwhp and 315.94rwtq (84% injector duty cycle- room to work with if we wanted to get more out of it at the cost of reliability.)
i have similar mods (all the boltons with stock turbo and motor) but with the twin power and at 14.5psi it makes 359.8. i'd run 16psi or more if i could but the car for some reason will only produce 14.5 psi...sometimes 15. oh yeah its tuned to 10.8 which i dont really like.
and get to the strip. let us know what she does.
Last edited by matty; 06-24-09 at 07:13 PM.
#380
Eats, Sleeps, Dreams Rotary
#381
improvisor specialist
iTrader: (2)
Join Date: Mar 2007
Location: lorain, ohio
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
just got back from tunning my car, heres my mod list first:
13b-re
half bridge port
turbonetics 62-1 .96 a/r
hks cast manifold
hks 50mm wg
hks ssqv
greddy fmic/2.75" pipping
bosch 044 fuel pump
1680/850 injectors
msd 6a/t2 leading coil
3" exhaust-borla xr1 muffler, vibrant resonator, apexi n1 muffler
power fc
tunned by: Logan from Defined Autoworks
420rwhp/315ftlbs @14psi
13b-re
half bridge port
turbonetics 62-1 .96 a/r
hks cast manifold
hks 50mm wg
hks ssqv
greddy fmic/2.75" pipping
bosch 044 fuel pump
1680/850 injectors
msd 6a/t2 leading coil
3" exhaust-borla xr1 muffler, vibrant resonator, apexi n1 muffler
power fc
tunned by: Logan from Defined Autoworks
420rwhp/315ftlbs @14psi
#382
Full Member
iTrader: (2)
Join Date: Nov 2008
Location: Florida
Posts: 67
Likes: 0
Received 0 Likes
on
0 Posts
I just had a tune done by Steve Kahn. I have a 94 FD stock twins, Greddy intake, PFC, Hi-Power and straight pipe. Those are all the mods I have. I made 297HP and 257FTLBS on a Dyno Jet at 11-12psi. Not bad in my opinion. I made 255 last time so I gained 42Hp with a PFC and exhaust.
Ooops forgot I have a Gotham down pipe also.
Ooops forgot I have a Gotham down pipe also.
#383
Magic Triangles no more!
Join Date: Mar 2007
Location: Tampa, FL
Posts: 285
Likes: 0
Received 0 Likes
on
0 Posts
* LS1 Block
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
#384
T O R Q U E!
iTrader: (24)
Damn that torque curve is sick. So your AFRs are around 12.5:1?
* LS1 Block
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
#385
Junior Member
Join Date: Jul 2008
Location: Brisbane, Aus
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
I'm making 280rwhp on 11PSI. RX7 Series 5 13Bturbo street port. Standard turbo, standard injectors, 3inch exhaust, front mount inter-cooler, microtech LT8s ECU. Boost controller is a turbosmart E-boost Street.
Engine isnt running lean as AFR starts at 13.5 and with WOT go to 11.
I was really stocked with these results. Was tuned on the Gold Coast here in Queensland, Australia by Dyson Rotary.
http://www.youtube.com/watch?v=NZYKJ2dFpzU
Engine isnt running lean as AFR starts at 13.5 and with WOT go to 11.
I was really stocked with these results. Was tuned on the Gold Coast here in Queensland, Australia by Dyson Rotary.
http://www.youtube.com/watch?v=NZYKJ2dFpzU
Last edited by ganador; 07-20-09 at 06:22 AM. Reason: AHHH, Wrong Section.
#386
Chasing numbers
iTrader: (5)
* LS1 Block
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
#388
Full Member
iTrader: (4)
Join Date: Dec 2007
Location: Houston
Posts: 110
Likes: 0
Received 0 Likes
on
0 Posts
Had the day off, went to the dyno. Low 100's air temps. . 50/50 Water/alcohol injection
Overall I was disappointed, the car was spooling too slowly, missing low end...and I thought the header was falling apart again after the first couple of low boost runs and a massive exhaust leak started. Happily I just found that I lost a turbo flange bolt, duh. So the repairs are holding but I think the header/DP combo is going to the trash bin anyway. Figured I'd post up anyway.
-On-center 62-1 BB, 0.96AR
-1680/850's,
-GM 3-bar
-Dual Coolingmist S-HSV's, direct lower intake primary tube injection, fully mapped with supplemental injector driver
-Mazda Trix street port exhaust, mild Marcus Williams porting on plates (looks nearly stock but cleaned-up a little)
-Power FC
-Old school Marcus Williams header and DP.
-374whp/289wtq uncorrected (391whp/302wtq STD corrected)
-22psi, 15-18 Max Knock
Max numbers were at 22psi, suspect that I'm nearing choke flow conditions someplace(intake ports?) as the gains from 17psi to 22 were really small. My goal is to have a driveable street car not a dyno star but it's failing on both accounts with these plots. Posted anyway because the max numbers are probably pretty close to what it'll do.
http://img.villagephotos.com/p/2004-...Dyno072709.jpg
Overall I was disappointed, the car was spooling too slowly, missing low end...and I thought the header was falling apart again after the first couple of low boost runs and a massive exhaust leak started. Happily I just found that I lost a turbo flange bolt, duh. So the repairs are holding but I think the header/DP combo is going to the trash bin anyway. Figured I'd post up anyway.
-On-center 62-1 BB, 0.96AR
-1680/850's,
-GM 3-bar
-Dual Coolingmist S-HSV's, direct lower intake primary tube injection, fully mapped with supplemental injector driver
-Mazda Trix street port exhaust, mild Marcus Williams porting on plates (looks nearly stock but cleaned-up a little)
-Power FC
-Old school Marcus Williams header and DP.
-374whp/289wtq uncorrected (391whp/302wtq STD corrected)
-22psi, 15-18 Max Knock
Max numbers were at 22psi, suspect that I'm nearing choke flow conditions someplace(intake ports?) as the gains from 17psi to 22 were really small. My goal is to have a driveable street car not a dyno star but it's failing on both accounts with these plots. Posted anyway because the max numbers are probably pretty close to what it'll do.
http://img.villagephotos.com/p/2004-...Dyno072709.jpg
#391
Full Member
iTrader: (4)
Join Date: Dec 2007
Location: Houston
Posts: 110
Likes: 0
Received 0 Likes
on
0 Posts
So I fixed the exhaust leak last night and figured-out the reason for the low numbers. It was the air filter; imagine that.
I spent the money on new housings, coated rotors, 3mm 2-piece NRS seals, built a custom fully mappable dual direct primary port water injection system, and on and on, and then slapped a too small eBay air filter on there...live and learn.
I spent the money on new housings, coated rotors, 3mm 2-piece NRS seals, built a custom fully mappable dual direct primary port water injection system, and on and on, and then slapped a too small eBay air filter on there...live and learn.
#392
Racing Rotary Since 1983
iTrader: (6)
not bad re hp peak but something needs work re midrange. you make 200 rwhp at 5150 which is way too late. the typical sheet for a turbo of your size is around 4200.
your ports flow a bunch since your hp peak is around 7200.
there are a number of possibilities.
howard coleman
your ports flow a bunch since your hp peak is around 7200.
there are a number of possibilities.
howard coleman
#393
Rotary Enthusiast
iTrader: (16)
My 1993 Mazda RX-7 put down: 327rwhp and 262rwtq @ 6500rpms -(stock injectors ran out of fuel)
Motor: 13B REW Streetported by David Jerome (2mm Atkins cryo treated)
Turbos: Stock Twins Full Non-Sequential (12psi.)
Tuner: Steve Kan (Dynolab in ATL)
Performance Mods: K&N Filters, 3in. heat-wrapped dp, Magnaflow Hi-Flow Cat, HKS Carbon ti, ACT street/strip disc clutch, ACT Prolite Flywheel, Koyo Radiator, Pettit AST, Greddy V-Spec FMIC, Magnecor Plug Wires, Apexi PowerFC, Turbosmart MBC, Nippondenso Fuel Pump, Megan Coilovers, Brembo Slotted/Crossdrilled Rotors, Hawk HPS Pads, & SS Clutch & Brake Lines.
This car is my DD and I was happy with what it put down. Its came a long way and I've put a lot of hard work into it. The engine was VERY well built and the tuner did an amazing job! Next will be a good set of 1300cc's, HKS Twin Power, and turn the boost up to: (14-15psi.)
- Zach Morgan
Motor: 13B REW Streetported by David Jerome (2mm Atkins cryo treated)
Turbos: Stock Twins Full Non-Sequential (12psi.)
Tuner: Steve Kan (Dynolab in ATL)
Performance Mods: K&N Filters, 3in. heat-wrapped dp, Magnaflow Hi-Flow Cat, HKS Carbon ti, ACT street/strip disc clutch, ACT Prolite Flywheel, Koyo Radiator, Pettit AST, Greddy V-Spec FMIC, Magnecor Plug Wires, Apexi PowerFC, Turbosmart MBC, Nippondenso Fuel Pump, Megan Coilovers, Brembo Slotted/Crossdrilled Rotors, Hawk HPS Pads, & SS Clutch & Brake Lines.
This car is my DD and I was happy with what it put down. Its came a long way and I've put a lot of hard work into it. The engine was VERY well built and the tuner did an amazing job! Next will be a good set of 1300cc's, HKS Twin Power, and turn the boost up to: (14-15psi.)
- Zach Morgan
#394
Junior Member
iTrader: (1)
Join Date: Aug 2008
Location: Switzerland
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Gone Dyno tune my 94' FD nxt Saturday, what do u think how much power I could get out of following modz:
Stock engine (241hp Europe Version)
stock twins
Carbon air intake
Koyo Radiator
Mazdaspeed Intercooler
Efini Y-pipe
3' DP
3' Catback
Reliability Mods
PFC+Controller
Any advise how to improve hp? Regarding the fact that I can not install a MP and not port the engine due to the very strict emission standards in Switzerland. Probably upgrading the fuel system would be my next performance mod:-P What max. power would be possible with keeping also the boost at moderate levels?
Stock engine (241hp Europe Version)
stock twins
Carbon air intake
Koyo Radiator
Mazdaspeed Intercooler
Efini Y-pipe
3' DP
3' Catback
Reliability Mods
PFC+Controller
Any advise how to improve hp? Regarding the fact that I can not install a MP and not port the engine due to the very strict emission standards in Switzerland. Probably upgrading the fuel system would be my next performance mod:-P What max. power would be possible with keeping also the boost at moderate levels?
#395
Finally Knows
iTrader: (21)
Join Date: Sep 2003
Location: Hawaii
Posts: 1,089
Likes: 0
Received 0 Likes
on
0 Posts
Gone Dyno tune my 94' FD nxt Saturday, what do u think how much power I could get out of following modz:
Stock engine (241hp Europe Version)
stock twins
Carbon air intake
Koyo Radiator
Mazdaspeed Intercooler
Efini Y-pipe
3' DP
3' Catback
Reliability Mods
PFC+Controller
Any advise how to improve hp? Regarding the fact that I can not install a MP and not port the engine due to the very strict emission standards in Switzerland. Probably upgrading the fuel system would be my next performance mod:-P What max. power would be possible with keeping also the boost at moderate levels?
Stock engine (241hp Europe Version)
stock twins
Carbon air intake
Koyo Radiator
Mazdaspeed Intercooler
Efini Y-pipe
3' DP
3' Catback
Reliability Mods
PFC+Controller
Any advise how to improve hp? Regarding the fact that I can not install a MP and not port the engine due to the very strict emission standards in Switzerland. Probably upgrading the fuel system would be my next performance mod:-P What max. power would be possible with keeping also the boost at moderate levels?
With those mods? Around 300rwhp@12psi.
#396
Full Member
Join Date: Jun 2006
Location: Lancaster, PA
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
* LS1 Block
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
* T-56 Transmission
* TSP PRC 5.3L Stage 2.5 Heads
* TSP Torquer v2 Cam 112 LSA
* Cometic .040" Head gasket
* MSD 8.5mm wires and protective boots
* Ported Throttle Body
* 25% Udnerdrive Pulley
* JTR/Sanderson 1 7/8th Long Tube Headers
* LS6 Intake Manifold
* TSP 7.400 Pushrods
* LS7 Lifters
* LS2 Lifter Trays
* LS6 Oil Pump
* NGK TR55 plugs
* Aluminum Driveshaft
* Exhaust: catless custom true dual 3" piping through Magnaflow X-pipe and 5" straight through Magnaflow mufflers
HP: 430 SAE
TQ: 386
#397
The wankel way!!
Join Date: May 2008
Location: New Zealand
Posts: 462
Likes: 0
Received 0 Likes
on
0 Posts
My car has been at the tuners for about 3 weeks (busted mazda speed diff/tune). After trying to get the 1680s to idle and improve off boost performance, we gave up and went for 1000cc Primarys. The car now idles, cold starts and runs a whole lot better.
When I dropped it off it made 480rwh on 15psi. After the tune on low boost it made the same power at 12psi and was a totaly different car off boost. Boost got turned up to 14psi and lost compression on the first pull .
Think its a side seal, so will be rebuilt and tuned in the next few weeks. Dyno sheets will be up asap, but its sounding promising. (this is the pump gas tune)
When I dropped it off it made 480rwh on 15psi. After the tune on low boost it made the same power at 12psi and was a totaly different car off boost. Boost got turned up to 14psi and lost compression on the first pull .
Think its a side seal, so will be rebuilt and tuned in the next few weeks. Dyno sheets will be up asap, but its sounding promising. (this is the pump gas tune)
#399
Junior Member
iTrader: (1)
Join Date: Aug 2008
Location: Switzerland
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Got a pretty good result: 312.9 rwhp and 297.8 rw torque-the torque is actually a bit lower as at a certain curve it couldn't be messured-have a look at my dyno sheet( no clue why!) . The messuring only went to 6500rpm...shouldn't the peak be arround 7k rpm?!?
#400
Got a pretty surprising result with 1Bar@stock twins: 312.9 rwhp and 403.77torque(the torque is actually about 10ft lower as at a certain curve it couldn't be messured ( no clue why!) next to that I was expecting a way lower result in rwhp. And also the messuring only went to 6500rpm...shouldn't the peak be arround 7k rpm?!?
I am aware that these are some weird numbers (especially for torque) for my pretty stock fd. Anyone any idea?
I am aware that these are some weird numbers (especially for torque) for my pretty stock fd. Anyone any idea?