400whp @ 15psi what turbo setup?
#1
Apex seal blower
Thread Starter
Join Date: Mar 2001
Location: Toronto, Ontario, Canada
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
400whp @ 15psi what turbo setup?
Ok,
I've done a lot searching on the forum, and asked a lot of people about their setups and now I'm asking the forum. I want to achieve 400whp @ 15psi, preferably with a quick spool up.
The story is I blew my motor last year after an injector failure which resulted in all 3 of my apex seals on my front rotor to shoot through my turbo. (Not a good time) So now I'm rebuilding my motor and setting everything up fresh.
The new motor will have 3mm apex seals and a street port. Standalone ECU is an E6K, 1600cc primaries and stock secondaries. Now my question is what turbo and intercooler setup would people suggest. As I said I want to make 400whp at 15psi. I have a boost controller so I will be switching between 12psi and 15 depending on how much power I want. I want it to have reasonably quick pick up i.e. pretty damn close to full boost by around 3.5K RPM.
For an intercooler I would like to use a SMIC so any suggestions on that would be welcome.
As for turbos I've been looking at the T04R, and the GT40R but am inclined to look at anyone which will match my needs.
Thanks,
Raven
1993 Vintage Red FD
I've done a lot searching on the forum, and asked a lot of people about their setups and now I'm asking the forum. I want to achieve 400whp @ 15psi, preferably with a quick spool up.
The story is I blew my motor last year after an injector failure which resulted in all 3 of my apex seals on my front rotor to shoot through my turbo. (Not a good time) So now I'm rebuilding my motor and setting everything up fresh.
The new motor will have 3mm apex seals and a street port. Standalone ECU is an E6K, 1600cc primaries and stock secondaries. Now my question is what turbo and intercooler setup would people suggest. As I said I want to make 400whp at 15psi. I have a boost controller so I will be switching between 12psi and 15 depending on how much power I want. I want it to have reasonably quick pick up i.e. pretty damn close to full boost by around 3.5K RPM.
For an intercooler I would like to use a SMIC so any suggestions on that would be welcome.
As for turbos I've been looking at the T04R, and the GT40R but am inclined to look at anyone which will match my needs.
Thanks,
Raven
1993 Vintage Red FD
#6
Brother of the Rotary
iTrader: (2)
Get that baby ready for the Ottawa Meet!!!!
I would say your best overall bet would be the T04S. Will give you the power you want and fairly quick spool up.
The GT35R is ballbearing, a more efficient design and will give you even better spool. But a bit more more expensive.
T04R is would be pretty laggy compared to your old setup.
I would say your best overall bet would be the T04S. Will give you the power you want and fairly quick spool up.
The GT35R is ballbearing, a more efficient design and will give you even better spool. But a bit more more expensive.
T04R is would be pretty laggy compared to your old setup.
#7
fart on a friends head!!!
to4s and 60-1 are supposed to be the same thing right??? thought i read that somewhere.
im running a 60-1. . . i should be able to hit 400rwhp at 15psi. . . considering my last attempt with a to4e hitting 347 at 14psi. hahaha. and that was with problems i wasnt even aware of!!!! anyways, 60-1 should suit you fine.
paul
im running a 60-1. . . i should be able to hit 400rwhp at 15psi. . . considering my last attempt with a to4e hitting 347 at 14psi. hahaha. and that was with problems i wasnt even aware of!!!! anyways, 60-1 should suit you fine.
paul
Trending Topics
#9
fart on a friends head!!!
1600s dont support idle very well. . . when building a car with a horsepower goal. you should buy injectors that suit your need. . . not injectors that over achieve. by doing so, you keep the injectors in an efficient range. fuel mileage will be better, etc, etc.
paul
paul
#10
I live in an igloo
Join Date: Jul 2004
Location: calgary alberta
Posts: 2,546
Likes: 0
Received 0 Likes
on
0 Posts
I see. But can't you tell the piggyback (SAFC) how much fuel the injector will put out? SO say at like 1000rpm and less you can have it runnin lean yes?
thx for the answers btw.
thx for the answers btw.
#11
Microtech Tuning!
Join Date: Feb 2002
Location: 626 Socal
Posts: 1,828
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BlaCkPlaGUE
I see. But can't you tell the piggyback (SAFC) how much fuel the injector will put out? SO say at like 1000rpm and less you can have it runnin lean yes?
thx for the answers btw.
thx for the answers btw.
#12
I live in an igloo
Join Date: Jul 2004
Location: calgary alberta
Posts: 2,546
Likes: 0
Received 0 Likes
on
0 Posts
wow now im confused. Isn't that what I just said?
Adding or subtracting fuel, is this not controlling an injector?
Bear with me please, once I get it, I'll get it..
Adding or subtracting fuel, is this not controlling an injector?
Bear with me please, once I get it, I'll get it..
#13
Brother of the Rotary
iTrader: (2)
^ I think what he is saying is, since the SAFC is a piggyback, you can only tell the ECU to add or remove fuel up to a certain %.
You can't control the actual injector pulsewidths (like you can with an EMS).
Huge 1600cc's are designed to dump a lot of fuel, it would be hard to get the fine control needed (small pulsewidth) at idle with those. People have done it though, just with big porting...
You can't control the actual injector pulsewidths (like you can with an EMS).
Huge 1600cc's are designed to dump a lot of fuel, it would be hard to get the fine control needed (small pulsewidth) at idle with those. People have done it though, just with big porting...
#14
development
As often as this exact question comes up "400hp @ 15psi" and all the responses are the same...
Let's have a check in.
Who has a running car with 400+rwhp @ 15psi or less psi (of course with quick spool, because that's what everyone wants )
is 400rwhp @ 15psi (with a quick spool )that easy and common?
Let's have a check in.
Who has a running car with 400+rwhp @ 15psi or less psi (of course with quick spool, because that's what everyone wants )
is 400rwhp @ 15psi (with a quick spool )that easy and common?
#15
Apex seal blower
Thread Starter
Join Date: Mar 2001
Location: Toronto, Ontario, Canada
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
Sorry yes 1600cc secondaries . So the GT35R should provide fast spooling and achieve 400WHP at around 15psi? What is the difference in spooling between the t60-1 and gt35R? I assume the t60-1 will be slightly slower anyone have an idea of where each would reach full boost?
Will a SMIC be sufficient, any recommendations?
Raven
Will a SMIC be sufficient, any recommendations?
Raven
#19
Apex seal blower
Thread Starter
Join Date: Mar 2001
Location: Toronto, Ontario, Canada
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
Glass man, I assume your saying you have 400whp @ 15psi. Can you tell me your setup? Turbo and IC, and approximately what rpm you get full boost.
#20
Will u do me a kindness?
iTrader: (2)
Originally Posted by raven bc
Glass man, I assume your saying you have 400whp @ 15psi. Can you tell me your setup? Turbo and IC, and approximately what rpm you get full boost.
A few more things, but that's most of the power or related modifications. I see full boost around 3,600 RPM.
#21
Originally Posted by the_glass_man
GT35R 1.06 A/R, 45mm wastegate, GReddy 3 row FMIC, 1600 secondaries, Denso pump, modified UIM and GReddy Elbow, Unorthodox Racing main pulley, removed airpump, a/c, powersteering, GReddy underdrive pulley kit, HKS Twin Power, PFC.
A few more things, but that's most of the power or related modifications. I see full boost around 3,600 RPM.
A few more things, but that's most of the power or related modifications. I see full boost around 3,600 RPM.
Also are you running stock ports and pump gas?
What were you're dyno #'s?????
Justus
sorry for all the ?? Glassman
#22
Rotary Enthusiast
iTrader: (1)
Join Date: Sep 2002
Location: Chicago, IL
Posts: 1,462
Likes: 0
Received 0 Likes
on
0 Posts
go with the GT40R... that will give you what you want... and then some Check the for sale section, I am selling mine for a good price brand new... and allready has had the manifolds ceramic coated and airfuel bung welded in.
Thread
Thread Starter
Forum
Replies
Last Post
immanuel__7
2nd Generation Specific (1986-1992)
89
09-05-15 10:23 AM