I77 & I40 Crossroads rotary meet
#4276
Eats, Sleeps, Dreams Rotary
iTrader: (4)
Join Date: Apr 2003
Location: Denver, NC
Posts: 3,531
Likes: 0
Received 0 Likes
on
0 Posts
Nice Sam, What are those off of? A S6 FD?
Got my turbo housing back today. Very pretty weld Except 1 spot where it was hard to get the tig into. But It looks great. Headed out now to swap everything back over to my FD to make it live again!! Headcutting commences tomorrow!!
Got my turbo housing back today. Very pretty weld Except 1 spot where it was hard to get the tig into. But It looks great. Headed out now to swap everything back over to my FD to make it live again!! Headcutting commences tomorrow!!
#4279
Eats, Sleeps, Dreams Rotary
iTrader: (4)
Join Date: Apr 2003
Location: Denver, NC
Posts: 3,531
Likes: 0
Received 0 Likes
on
0 Posts
It can ALWAYS get better P-Port Mazdaspeeds would do it for me And some Racing Beat Aluminum plates...mmmmmmmmmm
On another note, I friggin HATE V-Band clamps!! I have never had one seal properly more than once..I want a bolted/flange with a gasket..
Car is up and running again, other than the POS v-band leak
On another note, I friggin HATE V-Band clamps!! I have never had one seal properly more than once..I want a bolted/flange with a gasket..
Car is up and running again, other than the POS v-band leak
#4280
19 on 15lb.
iTrader: (2)
Join Date: Apr 2008
Location: Charlotte, NC
Posts: 427
Likes: 0
Received 0 Likes
on
0 Posts
From what I understand Lake Norman isn't all that far from O'Charlies am I right? You'd probably have time to make it there for a little before going to work since we're leaving at 1:45 to the Lake. I would just wear your work clothes so you don't have to go back to ya house or somethin
#4284
Eats, Sleeps, Dreams Rotary
iTrader: (4)
Join Date: Apr 2003
Location: Denver, NC
Posts: 3,531
Likes: 0
Received 0 Likes
on
0 Posts
Hey Bryan.. I remember holding the rear plate when I was there at the shop. Pretty sweet! Are you coming out tomorrow? Would be cool to have you there for the photos.
You don't happen to have a clutch master and slave for a FD laying around the shop would ya? And maybe a good drivers side engine mount?
You don't happen to have a clutch master and slave for a FD laying around the shop would ya? And maybe a good drivers side engine mount?
#4295
Zuuuummmmm Zuuuummmmm
Join Date: Oct 2006
Location: King, NC
Posts: 1,450
Likes: 0
Received 0 Likes
on
0 Posts
Ant, this is that video I was talking about with the 4 rotor
https://www.rx7club.com/rx-7-audio-visual-lounge-143/handbuilt-4rotor-809941/
https://www.rx7club.com/rx-7-audio-visual-lounge-143/handbuilt-4rotor-809941/
#4297
Waffles - hmmm good
iTrader: (1)
Headed out to wash the car now. See you guys at 1.
Kory get a pair and bring FC out to play
Too bad Ray couldn't make it up today, but we have Kent and buddy so that makes up for it.
Kory get a pair and bring FC out to play
Too bad Ray couldn't make it up today, but we have Kent and buddy so that makes up for it.