I think Pica car should be making as much power as this car or more. Hes run a 7.13 @191 but his car is much heavier (3/4 chassis). If pica makes it in the 6's, or even closer to it, it would be even more impressive.

besides, no one knows how much power this car is making unless they no how much it weighs.

Still very happy to see the 13b in the 6's. hope to see even lower very soon.

 

If Sporty rx-7 is 1800-1900 lbs we are looking at 1050-1150 horsepower which is pretty decent for those two triangles.

 

Is that really how much the car weighs?

 

In the engine world they said if you make 1 HP per Cubic inch your doing pretty good. Then if you make 100HP per litre your doing very well.. Now that your damn near 1000 per litre, that must just be unfathomable to whoever came up with those sayings!

Congrats

 

well that depends on what you think the rotary engines displacement really is .

 

Yes, I'd like to post a story at RN.COM about the 13B record, and would like to include as many facts as possible. So if anyone has access or can point me in the right direction. Thanks, -Bern

 

It's running NRS Ceramic Power Seals 3mm 1pc on 40 psi, that I know for sure

 

Probably you should show him the latest dyno sheets!

 

Jsut give him gaby's contact info.

 

post it here.

 

I don't have a dyno sheet past the last one but I have asked Gaby for a current one if it is available. Here is the one I have:



They take the engine to 10,500 rpm and Gaby tells me the engine is making over 1000 hp from this graph and power was increasing to the 10,500 rpm mark and beyond. This prompted Gaby to ask me if there was a limit (rpm) to where they would stop making power. "I don't know" I said "why don't we find out?".

There was an issue with the turbo on the run and they have corrected that so an updated graph will tell the full story. I'll post it on the seal thread when I get it.

Bern if you want to pm me I can give you Gaby's contact info so you can get the facts together for your article.

 

Theres a video on youtube of the car making 3 dyno pulls . the car makes 980hp at 43psi

 

You think they are going to show what their engine is really putting out?
980 is a little on the conservative side I would say.

 

very nice

 

That's probably the old dyno, the same one that was posted here a while ago.

 

I talked to Gaby yesterday and they have not been on the dyno since the last graph. He is going to do another session in mid Jan 08.

 

I got a local magazine article with some details on this car! (i can scan it if u want but its in spanish)

980whp 550wtq

Tim McAmis built full chassis with 104" wheelbase

front Strange double adjustable dampers with Hypercoil springs

Koni double adjustable rears

GooodYear 32x14.5x15 tires on Weld Racing Aluma Star Wheels

10,500 rpm

Extreme Rotaries center bearing billet eccentric shaft and engine balance

Extreme Rotaries stud kit

'88 8.5:1 rotors

'86 corner seals

2mm Australian apex seals <<<<just quoting what the magazine says

'94 Semi PP rotor housings by Gaby Skern, engine built in PR by him

Mike Turbo custom 88mm turbo with 5" down pipe

40psi controlled by Turbo Smart eboost-2

Gaby Skern custom turbo mani and billet aluminum intake mani built by Limon Machine Shop

Accufab 80mm throttle

Rons Fuel mechanical fuel fump (methanol)

3 Wilson Manifold fuel rails with a total of 12 1600cc injectors

'89 Cosmo ignition system with 2 MSD DIS-4 and 4 MSD Blaster DIS coils

Microtech LT12S X6 tuned by Gaby Skern

Jerico air shifted 5sp tranny with Gaby Skern specified and non-disclosed gear ratios

McLeod Clutch and Flywheel with Trick Titanium safety shield

Ford Mark Williams differential with "40 gun drill" shafts (whatever that means)

Best time:
1.07 sec 60'
4.50 sec 1/8 mile @ 165mph
6.97 sec 1/4 mile @ 197.7mph

 

Well they got at least two things wrong . Where do they get their info from???
- No center bearing crank
- NRS 3mm 1pc ceramic power seals. Which means the corner seals are wrong too.
It's shameful to see some other seals taking credit for NRS Power.

These guy's should get it right before putting it to print!!! What magazine is this?

 

Interesting... I was under the impression that car was running Metal apex seals too..

 

That car is also making alot more than 980 so I was say they got more than two things wrong

 

Gaby been using NRS Ceramics since 2005

 

ill scan it later but here's a video interview with Eddie "Sporty" Colon and he confirms the 980whp, the nrs seals, the extreme rotaries stud kit and "ball bearing" eccentric shaft

http://youtube.com/watch?v=YhXLs_Bwgsc

 

sorry it took so long!

 

i can translate if you want

 

I just want the contact info for the mag.