Power FC What knock reading is normal?
#1
Senior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2001
Location: long beach, ca
Posts: 363
Likes: 0
Received 0 Likes
on
0 Posts
What knock reading is normal?
i just got my car running again and im getting knock reading up to 22. Is that normal or too high?Im still break-in my motor, so im not driving it hard yet. I had XS tune a base map with my mods. I just want to blow my motor again. so im alitte worry.
#5
Full Member
Join Date: Dec 2001
Location: San Francisco
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Mine knocks at close to 100 regularly, hit 189 a few times. Engine still going strong, so go figure.
Originally posted by Swamp RX-7
****, mine knocked at 89 once, but it was at like 2000rpms under light throttle. Is that bad? It dosen't knock higher than 38 under WOT.
****, mine knocked at 89 once, but it was at like 2000rpms under light throttle. Is that bad? It dosen't knock higher than 38 under WOT.
Trending Topics
#9
Page 13 of the instruction manual says:
"There is no value to the Knock level. Please use it as a reference for tuning"
Basically, if you're always in the 20s but then one day you hit 150, that's probably bad. If you're always around 100 and your motor hasn't blown up yet, it's probably normal. I think each car will have different "normal" knock readings.
"There is no value to the Knock level. Please use it as a reference for tuning"
Basically, if you're always in the 20s but then one day you hit 150, that's probably bad. If you're always around 100 and your motor hasn't blown up yet, it's probably normal. I think each car will have different "normal" knock readings.
#10
1JZ powered
Join Date: Jul 2001
Location: Where there's only two seasons, hot and wet! I love Okinawa
Posts: 4,423
Likes: 0
Received 0 Likes
on
0 Posts
I've been railing and railing on my engine and have been getting an average knock of about 20 or so. I just recently took it out all the way through the middle of 4th Gear, it read a WHOPPING 14!!!...
...then again, when I get on really bad roads, my knock seems to go up...
...or when I don't fill up on Gas...
...then again, when I get on really bad roads, my knock seems to go up...
...or when I don't fill up on Gas...
#11
20B N/A Wide Body FC3S
You all need to get a wrench and tork your knock sensors... I may go down... those are actually some slightly dangerous knocks regardless of what the manual says...
#12
Junior Member
Join Date: Dec 2001
Location: Snellville, GA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Be careful torquing your knock sensors, the sensor is very difficult to gain access to, and I broke mine trying to torque it.
Does anyone see any harm in running without a knock sensor? I haven't had one on my car for over a month and so far it's been completely innocuous.
Does anyone see any harm in running without a knock sensor? I haven't had one on my car for over a month and so far it's been completely innocuous.
#13
Full Member
Join Date: Apr 2001
Location: Modesto, CA
Posts: 212
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Scott Olsen
Be careful torquing your knock sensors, the sensor is very difficult to gain access to, and I broke mine trying to torque it.
Does anyone see any harm in running without a knock sensor? I haven't had one on my car for over a month and so far it's been completely innocuous.
Be careful torquing your knock sensors, the sensor is very difficult to gain access to, and I broke mine trying to torque it.
Does anyone see any harm in running without a knock sensor? I haven't had one on my car for over a month and so far it's been completely innocuous.
You big muscle man....
-Matt
#14
Junior Member
Join Date: Dec 2001
Location: Snellville, GA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Heh, tell me about it.. It's strange, I'm not even sure what I did to my knock sensor. It just stopped working and would just display "1" on the monitor screen. Before that I was consistently getting knock readings in the 100's.
Anyhow, there's no way I'm going to go buy another $200 microphone from Mazda just to get a bunch of arbitrary readings.
Anyhow, there's no way I'm going to go buy another $200 microphone from Mazda just to get a bunch of arbitrary readings.
Last edited by Scott Olsen; 03-21-02 at 11:09 PM.
#15
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by potatobbq
Page 13 of the instruction manual says:
"There is no value to the Knock level. Please use it as a reference for tuning".....
Page 13 of the instruction manual says:
"There is no value to the Knock level. Please use it as a reference for tuning".....
I'm just curious...if the knock reading as no true meaning, then what exactly DOES it mean?
Does ANYONE know what figure in the knock means that you are detonating? It's there so it MUST mean soemthing.
#17
OK, I'll bite and ask the obvious dumb question. It was my understanding that the stock ECU didn't include any retard based on knock, thus the "need" for people to put the aftermarket system on. So what the hell is the sensor even for???? I didn't think it ever triggered anything like a check engine light. Maybe it was thrown in there in the early design stages and then Mazda realized it wasn't reliable and just decided not to use it?
For the record, I generally see 30's on mine, but at WOT redline runs I see occasional peaks of 100. Unfortunately I haven't been able to catch it on a graph of knock vs RPM yet to figure out if maybe it's just noise from shifting or anything. Was racing a 928 this morning and then looked down and saw the peak of 100....
For the record, I generally see 30's on mine, but at WOT redline runs I see occasional peaks of 100. Unfortunately I haven't been able to catch it on a graph of knock vs RPM yet to figure out if maybe it's just noise from shifting or anything. Was racing a 928 this morning and then looked down and saw the peak of 100....
#18
Senior Member
Join Date: Jun 2001
Location: Charleston SC
Posts: 252
Likes: 0
Received 0 Likes
on
0 Posts
The Stock ECU did have a timing retard function for knock but it was only 4-6 degrees. which works with a stock setup but once you start making more power it's just not enough. The PFC has no knock retard. You can run a J&S but it only does the leading plugs so it has limits and issues too. I've seen that the values from THe PFC are as stated above, a value that changes car to car.
#19
Cool, I had never read anywhere about the stock retard. By the way, for what it's worth I caught my knock peak yesterday on the graph, and it happened at 7500 right at the peak RPM when I shifted and stopped accelerating. Just one spike. Probably noise.
#20
WTF is wrong with it now?
Join Date: Oct 2001
Location: London, ON
Posts: 1,492
Likes: 0
Received 0 Likes
on
0 Posts
My knock reading shoots upwards when I blip the throttle. I've read somewhere that the stock knock sensor has a hard time distinguishing normal engine noises above 3000 RPM from detonation. This was from someone selling the J & S, I think. Anyway, It sounds like this is true if bumps in the road affect the reading. It must be at least partially effective, as when I test drove my car before I bought it, it would puff black smoke at startup and when blipping the throttle. I saw the guy put in 89 octane, and when I started putting in 94, I never saw the black smoke again. I believe it was retarding the ignition enough to run really rich.
#21
OH OK, check this out, I though I put this out, but maybe not. This problem has came up a lot, many different people and APEXi, RE-Amemiya and a few other
companies say the same thing, the stock knock sensor is GARBAGE!!!. If you worried about get an aftermarket sensor, or something. This happens only with the POWER FC that I have heard, APEXi says its the car, and Im sure if I asked MAZDA they would say it APEXI, bottom line if you have the power FC just turn off the Knock warning and dont view the knock level.
If you have more question feel free
Jason
JT-Imports
Yokohama Japan
www.jt-imports.com
companies say the same thing, the stock knock sensor is GARBAGE!!!. If you worried about get an aftermarket sensor, or something. This happens only with the POWER FC that I have heard, APEXi says its the car, and Im sure if I asked MAZDA they would say it APEXI, bottom line if you have the power FC just turn off the Knock warning and dont view the knock level.
If you have more question feel free
Jason
JT-Imports
Yokohama Japan
www.jt-imports.com
#22
1JZ powered
Join Date: Jul 2001
Location: Where there's only two seasons, hot and wet! I love Okinawa
Posts: 4,423
Likes: 0
Received 0 Likes
on
0 Posts
I think the stock knock sensor is garbage also, but I know that I have HEARD knock, and looked up at the PFC and there it was...78 reading. Normally, it will stay around 20 or so, and it will run great. But I must have gotten a bad batch of gas or something because at 6000 rpm's, it started to run like crap and then "bang"...knock...
#23
Senior Member
Join Date: Oct 2001
Location: NNJ
Posts: 567
Likes: 0
Received 0 Likes
on
0 Posts
Up until recently, my highest reading was arnd 100-120. I just installed my M2 CAI and Efini y-pipe a week ago and this past Saturday for the first time I noticed readings up to 159 which is the highest Ive ever seen. But Ive only owned my car since last fall.......so I dont know if my mods, outside temps or a combination of both has somethng to do with it. One thing I think I noticed is it seems to go haywire if Im goin uphill (even slightly) in a higher gear running low revs.
Anyone else notice when theirs is goin a lil crazy?
Anyone else notice when theirs is goin a lil crazy?
#24
Senior Member
Join Date: Feb 2002
Location: Seattle / Bothell
Posts: 339
Likes: 0
Received 0 Likes
on
0 Posts
Well, if its anything like my prelude's knock sensor, basically there is a bit of variance between the sensors. If you change knock sensors then you end up having to re-tune your j&s to the new one. I'm not sure if its like that on the FD, but I would imagine so, which would explain why they say that it should be around the same reading and not jump alot higher, but that the base isn't super important.
#25
FB=OS Giken LSD
iTrader: (20)
Join Date: Apr 2001
Location: Wilmington, DE
Posts: 2,279
Likes: 0
Received 0 Likes
on
0 Posts
Here is stupid question #2:
I don't have a knock sensor. With my Haltech setup, how much retard should I run with each pound of boost? I'm new in the turbo world and I don't know the basics.
I don't have a knock sensor. With my Haltech setup, how much retard should I run with each pound of boost? I'm new in the turbo world and I don't know the basics.