Power FC lc1 wideband and datalogit setup
#1
Senior Member
![](https://www.rx7club.com/images/misc/10_year_icon.png)
Thread Starter
iTrader: (1)
Join Date: May 2009
Location: greece
Posts: 419
Likes: 0
Received 0 Likes
on
0 Posts
lc1 wideband and datalogit setup
hi,
can anyone please help me to tune properly the lc1 ans datalogit to work together?
is this correct:
Set the fc edit “Analog Out 1” to the following:
a. 0 Volts at AFR: 9.0
b. 5 Volts at AFR: 16.0
also set the same to the LC1 setup?
the lc1 manual suggests the above but as i can see at the auxiliary screen setup for the An1 at the fcedit the numbers do not much :
the fc edit witch i have has:
a. 0 Volts at AFR: 10
b. 5 Volts at AFR: 20
and it is the v2.126 .
so witch one is the correct?
thanks guys!!
can anyone please help me to tune properly the lc1 ans datalogit to work together?
is this correct:
Set the fc edit “Analog Out 1” to the following:
a. 0 Volts at AFR: 9.0
b. 5 Volts at AFR: 16.0
also set the same to the LC1 setup?
the lc1 manual suggests the above but as i can see at the auxiliary screen setup for the An1 at the fcedit the numbers do not much :
the fc edit witch i have has:
a. 0 Volts at AFR: 10
b. 5 Volts at AFR: 20
and it is the v2.126 .
so witch one is the correct?
thanks guys!!
#2
hi,
can anyone please help me to tune properly the lc1 ans datalogit to work together?
is this correct:
Set the fc edit “Analog Out 1” to the following:
a. 0 Volts at AFR: 9.0
b. 5 Volts at AFR: 16.0
also set the same to the LC1 setup?
the lc1 manual suggests the above but as i can see at the auxiliary screen setup for the An1 at the fcedit the numbers do not much :
the fc edit witch i have has:
a. 0 Volts at AFR: 10
b. 5 Volts at AFR: 20
and it is the v2.126 .
so witch one is the correct?
thanks guys!!
can anyone please help me to tune properly the lc1 ans datalogit to work together?
is this correct:
Set the fc edit “Analog Out 1” to the following:
a. 0 Volts at AFR: 9.0
b. 5 Volts at AFR: 16.0
also set the same to the LC1 setup?
the lc1 manual suggests the above but as i can see at the auxiliary screen setup for the An1 at the fcedit the numbers do not much :
the fc edit witch i have has:
a. 0 Volts at AFR: 10
b. 5 Volts at AFR: 20
and it is the v2.126 .
so witch one is the correct?
thanks guys!!
I was way off having the LC-1's output set to 0vdc=9 and 5vdc=16
I changed LC-1 analog output to 0vdc=9 and 5vdc=19
Then on the FC-Edit, Aux Setup, check the a,b,c values for poly on your wideband channel (usually AN-1 or AN-2)
Mine is seutp as a=0, b=2, c=9, and now I'm within 0.3 of the XD-1 display.
Also, confirm you LM-1 ground is either hooked-up to the DL's 0-VDC, or if connected to the DL's AN-2, you have the "AN1-AN2 " box checked.
:-) neil
#4
Senior Member
![](https://www.rx7club.com/images/misc/10_year_icon.png)
Thread Starter
iTrader: (1)
Join Date: May 2009
Location: greece
Posts: 419
Likes: 0
Received 0 Likes
on
0 Posts
i will use the An2 as a ground , so i will check the AN1-An2 box.
do i need to enter any value at the lc1 setup for the An2 output?
the fc edit an2 setup screen have 0-5v and 0-5v values as default.do i need to enter the same at the lc1 's setup screen for the An2 ? 0-5v and 0-5v?
thanks!!!!
do i need to enter any value at the lc1 setup for the An2 output?
the fc edit an2 setup screen have 0-5v and 0-5v values as default.do i need to enter the same at the lc1 's setup screen for the An2 ? 0-5v and 0-5v?
thanks!!!!
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
PinkRacer
2nd Generation Specific (1986-1992)
43
10-01-15 09:13 AM