Power FC Japanese Power FC..works here on the US versions?
08-26-05, 10:24 PM
#26
127,338 OEM, 11.5psi
Join Date: Jun 2005
Location: MARYLAND
Posts: 936
Likes: 0
Received 0 Likes
on
0 Posts
i have a PFC from AP ENGINEETRING AND FOLKS SAID THAT IT WOULDNT WORK ON MY FD BECUASE THEY MIGHT HAVE MESSED WITH THE ROM CHIP,. THE CAR IS FINE AND ALL I DID WAS DUMP THE BASE MOD MAP BACK INTO IT AND IT STARTED UP AND EVERYTHING OOOO YEA GO TO THE PFC POST AND READ THE STICKY ITS SOME REALLY GOOD INFO.
08-27-05, 05:51 PM
#30
Originally Posted by Gouki7
ok so is this pic correct? Cuz I got a power fc for pretty cheap from Up-Garage. Or is it different w/ the different series of power fc's
(Scans are too large to upload)
Page 1: http://img.villagephotos.com/p/2004-...tructions1.jpg
Page 2: http://img.villagephotos.com/p/2004-...tructions2.jpg
~Ramy
08-31-05, 01:15 PM
#32
Rotary Enthusiast
Thread Starter
Join Date: Jan 2004
Location: CSU Long Beach
Posts: 756
Likes: 0
Received 0 Likes
on
0 Posts
Ok so I installed it without cutting the wires and it seems to be running fine. Although it's learning so it's running funny till 150 miles =p
08-31-05, 09:07 PM
#33
After all this, you installed it w/o cutting wires? God...it's wasted effort helping some ppl... And where'd you get this 150 miles BS? The PFC will learn your idle if you FOLLOW THE INSTRUCTIONS on the spot. Takes about 30 minutes.
Seriously, if you aren't going to follow directions, or listen to the advice of those who know more than you, please just save us the time and don't ask. Really.
Seriously, if you aren't going to follow directions, or listen to the advice of those who know more than you, please just save us the time and don't ask. Really.
09-03-05, 04:15 PM
#34
Rotary Enthusiast
Thread Starter
Join Date: Jan 2004
Location: CSU Long Beach
Posts: 756
Likes: 0
Received 0 Likes
on
0 Posts
well I was at Rotary Power and they said not to cut it and see if it runs because some of them according to them, some power fc's run fine without cutting them. And I was told by their Power FC tuner that it'll learn till about 150 miles the car, not the idle the idle is fine. So I WAS listening to those that know more than me. If you want to be a jerk about it. Geez what ran up your butt? If it doesn't work after then I'll cut the wires like you said. I'm not disregarding the info you guys gave me. Just following some instructions that a reputable shop gave me. That was seriously the worst I've been flamed on here about something so small, I'm not a little kid, yeah I'm young but I've been around cars quite a bit and I can see how some people get offended because of us here on this board.
Last edited by Gouki7; 09-03-05 at 04:31 PM.
09-04-05, 02:12 AM
#35
Rotary Enthusiast
Thread Starter
Join Date: Jan 2004
Location: CSU Long Beach
Posts: 756
Likes: 0
Received 0 Likes
on
0 Posts
anyway. I'll heed everyone's advice and remove the wires. They have the tool to actually take them out of the wiring harness. (Much easier than the good ole paper clip). I'll let you guys know what the update is.
Thread
Thread Starter
Forum
Replies
Last Post
