Power FC HELP:850 primaries installed-, breakup during transition
#1
Senior Member
![](https://www.rx7club.com/images/misc/15_year_icon.png)
Thread Starter
Join Date: Jun 2003
Location: west palm beach, FL
Posts: 660
Likes: 0
Received 0 Likes
on
0 Posts
HELP:850 primaries installed-, breakup during transition
Ok my mods are, downpipe,streetport, intake, catback, stock gutted midpipe, pulleys, front mount and power fc..relevent mods anyhow..
Well I just installed some 850CC injectors in the primary slots, and I noticed during second gear and up during the transition i get harsh breakup. I was wondering if this was due to me not resetting my ecu by disconnecting my battery or incorrect settings on my power fc. I am running a basemap from this basemap site, with same mods as me. I did however change the injector settings on the pfc to the following:
FR.PR 64.5% +0.04 ms
RR.PR64.5% +0.04 ms
While it is nice to get a 70% duty cycle at +- 13psi, it is not nice to have a nasty breakup in second gear causing the car to surge. Any help would be appreciated.
Also the map im running is the suganuma map off this site.
Well I just installed some 850CC injectors in the primary slots, and I noticed during second gear and up during the transition i get harsh breakup. I was wondering if this was due to me not resetting my ecu by disconnecting my battery or incorrect settings on my power fc. I am running a basemap from this basemap site, with same mods as me. I did however change the injector settings on the pfc to the following:
FR.PR 64.5% +0.04 ms
RR.PR64.5% +0.04 ms
While it is nice to get a 70% duty cycle at +- 13psi, it is not nice to have a nasty breakup in second gear causing the car to surge. Any help would be appreciated.
Also the map im running is the suganuma map off this site.
Last edited by ghostrx7; 12-13-03 at 11:12 PM.
#4
Senior Member
![](https://www.rx7club.com/images/misc/15_year_icon.png)
Thread Starter
Join Date: Jun 2003
Location: west palm beach, FL
Posts: 660
Likes: 0
Received 0 Likes
on
0 Posts
Actually i think i may have figured out why, but i cannot test it because its raining outside, its either what i thought before or, its pfc sensing overboost and cutting fuel.
Trending Topics
#10
Senior Member
![](https://www.rx7club.com/images/misc/15_year_icon.png)
Thread Starter
Join Date: Jun 2003
Location: west palm beach, FL
Posts: 660
Likes: 0
Received 0 Likes
on
0 Posts
Ok figured out the problem....BAD PLUGS, LOL, first thing i should have checked for, anyways, i also get break up still but that is due to my car running extremely rich at anything past 13 psi. Wish i could go test drive my car, but my master cylinder crapped on me and the brakes keep locking up.
#11
First thing you should do is turn the boost down and drive easily until you can get a wideband on there.
13 psi with those mods and the base map will be lean. I'm assuming by base map you mean the default map that comes with the PFC. That map doesn't have enough fuel for your mods and the timing is to aggressive for street port.
Jack
13 psi with those mods and the base map will be lean. I'm assuming by base map you mean the default map that comes with the PFC. That map doesn't have enough fuel for your mods and the timing is to aggressive for street port.
Jack
Thread
Thread Starter
Forum
Replies
Last Post
Turblown
Vendor Classifieds
12
10-17-20 03:25 PM
eplusz
General Rotary Tech Support
15
10-07-15 04:04 PM