Power FC Bought used power fc.How do I reset to base map
10-11-10, 09:12 PM
#3
Senior Member
Thread Starter
iTrader: (7)
Join Date: Nov 2009
Location: murrieta, CA
Posts: 503
Likes: 0
Received 0 Likes
on
0 Posts
Ok so I did what you said with the commander. I turned the key on and the check engine light does not come on, that can't be good. Haha. But it works fine with the stock ecu
10-11-10, 09:58 PM
#4
The check engine light does not come work with the Power Fc. That’s why you get the sensor check option with the power fc. That way you can see which sensor readings are off.
10-12-10, 10:35 AM
#5
Senior Member
Thread Starter
iTrader: (7)
Join Date: Nov 2009
Location: murrieta, CA
Posts: 503
Likes: 0
Received 0 Likes
on
0 Posts
Ok. I reset te power fc and my car will not start... I did what the instructions said and plugged the stock ecu back in, start Your car and then plug the power fc in... Still nothing... Now what?
10-12-10, 06:00 PM
#8
Rotary Enthusiast
iTrader: (28)
Join Date: Aug 2008
Location: Miami, FL
Posts: 1,149
Likes: 0
Received 0 Likes
on
0 Posts
Check that the turbo control feature in the /etc->functions menu is turned off. It should be the first setting, and off starts with what looks like a "t" in jap. That may be what's causing the car to not turn on.
10-12-10, 06:14 PM
#9
The sequential turbo control setting has no effect on low load situations. All it does is change the behavior of the wastegate control, precontrol, charge control, charge relief, and turbo control solenoids. None of these solenoids do anything when the engine is out of boost.
I actually have sequential turbo control enabled on my single turbo car. This keeps the PFC boost control system functioning so that you can control boost on a single turbo car using the PFC.
I actually have sequential turbo control enabled on my single turbo car. This keeps the PFC boost control system functioning so that you can control boost on a single turbo car using the PFC.
10-13-10, 09:57 AM
#11
Rotary Enthusiast
iTrader: (28)
Join Date: Aug 2008
Location: Miami, FL
Posts: 1,149
Likes: 0
Received 0 Likes
on
0 Posts
The sequential turbo control setting has no effect on low load situations. All it does is change the behavior of the wastegate control, precontrol, charge control, charge relief, and turbo control solenoids. None of these solenoids do anything when the engine is out of boost.
I actually have sequential turbo control enabled on my single turbo car. This keeps the PFC boost control system functioning so that you can control boost on a single turbo car using the PFC.
I actually have sequential turbo control enabled on my single turbo car. This keeps the PFC boost control system functioning so that you can control boost on a single turbo car using the PFC.
10-17-10, 12:07 PM
#14
REPU Garage
iTrader: (17)
Join Date: Jun 2007
Location: Northern Colorado
Posts: 623
Likes: 0
Received 0 Likes
on
0 Posts
Just ***** and grins, what is the SN # of your PFC? I sent my broken one back to the original seller, and it wouldn't be beneath him to lie to others and sell it to someone else
mine was PFC FD3S4 020-1409
10-18-10, 11:10 PM
#15
I sold him that PowerFC. It ran in my car just fine. I have no reason to lie. I also loaded up the stock map for him through my Datalogit. I didn't know you could do it through the commander :/
serial number 010-0830
serial number 010-0830
Last edited by Aeka GSR; 10-18-10 at 11:18 PM.
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
stickmantijuana
Engine Management Forum
11
11-09-15 01:15 PM
befarrer
Microtech
3
08-22-15 05:52 PM
