Originally Posted by dznutzuk
(Post 11095733)
Aha, I see, well if you do get one see if you can use a 4wire GM unit, it's much better than a bac valve.
|
3 Attachment(s)
Here are a few pics of the new installed turbo beanie and some of the car in the parking lot at the office...Now just need to take care of all the scratches, dings and all around general neglect of the paint for the past 1.5 years...
I also got my exhaust valve working remotely so now I push a button on a "fob" and the exhaust opens fully or shuts off completely which makes the car almost as quiet as stock. On another note, i have an oil leak and I cannot determine the source. So far I have been able to determine that it only occurs when the engine is running and that it drips near the back of the engine. I have reduced it to two possible scenarios, the oil pan is not fully sealed on the back area or my rear retainer/seal for the eccentric is allowing oil to seep through. Im hoping its the first and not the latter since an oil pan change is super easy on this car...We'll see C Attachment 718326 Attachment 718327 Attachment 718328 |
Originally Posted by angeljoelv
(Post 11096762)
Im also using the gm 4 wire in the 20b and that thing makes it idle like a charm..
|
1 Attachment(s)
Small Update...
I've been driving the car for the past week and a half and so far it has gone 155miles. I began using Klotz Benol premix (E85) as supplemental lubrication to the OMP. So far I got the car to where it drives ok and I just want to work out small kinks here and there regarding little leaks and such. The injectors I've been using so far are as follows: Primaries: 2 X Modified OEM RX-8 2ndaries (supposed to flow about 650-720cc but unknown) Secondary 1's: 2 X Modified OEM RX-8 primaries (supposed to flow about 650-720cc but unknown) Secondary 2's: 2 X 1680cc Low Impedance Before, I didn't have any issues with a similar combination but now it seems as though the primaries are not enough to handle the required PUMP1 and PUMP2 values with this engine that are supposed to compensate for tapping on the throttle or quick throttle changes. Being as though I knew this setup is not enough anyways I had ordered some 2000cc High Impedance units from Five-O that I will install in the primary location. We'll see how it goes when I install them. Cheers! Attachment 718329 |
Originally Posted by chrisrx8pr
(Post 11096954)
here are a few pics of the new installed turbo beanie and some of the car in the parking lot at the office...now just need to take care of all the scratches, dings and all around general neglect of the paint for the past 1.5 years...
I also got my exhaust valve working remotely so now i push a button on a "fob" and the exhaust opens fully or shuts off completely which makes the car almost as quiet as stock. On another note, i have an oil leak and i cannot determine the source. So far i have been able to determine that it only occurs when the engine is running and that it drips near the back of the engine. I have reduced it to two possible scenarios, the oil pan is not fully sealed on the back area or my rear retainer/seal for the eccentric is allowing oil to seep through. Im hoping its the first and not the latter since an oil pan change is super easy on this car...we'll see c https://i679.photobucket.com/albums/...g?t=1337542932 https://i679.photobucket.com/albums/...g?t=1337542933 https://i679.photobucket.com/albums/...g?t=1337542939 |
Wow... Looking good!
What, you didn't like turboman or ford blue? Haha, in for dyno vids! |
Originally Posted by nuimpykid
(Post 11120692)
Wow... Looking good!
What, you didn't like turboman or ford blue? Haha, in for dyno vids! I'm finally starting to tune the upper end and I all can say is wow...its starting to become a fast animal...:) Will post vids when I finally have time to put it on the dyno, in the meanwhile, its country road tuning for me...;) Cheers! |
12 Attachment(s)
Quick update...Car has been driving for about 1200 miles and is pretty much tuned at 14-15psi. I'm happy to have it back and it feels good even at this low boost...we will see when I turn it up to 20 or so.
On another note, a brake upgrade was always in the plans and of course I always like to do things the hard way so I decided to move forward with a corvette Z06 brake upgrade...14.0" X 1.26" Rotors and huge 6 piston calipers... Cheers! Attachment 718330 Attachment 718331 Beginning of the brakets... Attachment 718332 Attachment 718333 Attachment 718334 Attachment 718335 Attachment 718336 Attachment 718337 Attachment 718338 Attachment 718339 Attachment 718340 Attachment 718341 |
Great build! Those brakes are cause the '8 to do a stoppie when you jump on them!! :D
|
8 Attachment(s)
Hello Peeps, its been a while.
I finally got around to relocating the ECU and Microtech up to the front behind the bumper where it is away from turbo heat. As a bonus its really cleans up the engine bay to have this out of there. Made a neat little aluminum box for housing all this stuff up front...50+ wires stretched later...my face speaks for itself... Cheers! Attachment 718342 Attachment 718343 Attachment 718344 Attachment 718345 Attachment 718346 Attachment 718347 Attachment 718348 Attachment 718349 |
You should put a Turbonetic Inlet Horn ! I would look sick
|
Originally Posted by vrx8
(Post 11196202)
You should put a Turbonetic Inlet Horn ! I would look sick
C |
Horn? Velocity stack people... :)
|
Originally Posted by angeljoelv
(Post 11196897)
horn? Velocity stack people... :)
|
^^ Same shit different toilet lol
|
Lol... just. Busting your balls
|
Any updates you would like to share?
|
Originally Posted by GAMBEAN
(Post 11227392)
Any updates you would like to share?
I will be switching to a Haltech Sprint RE to allow better tuning during throttle transition (probably will do this during winter). The Microtech's simplistic "Pump" settings just aren't cutting it and the car is street driven all the time so flat spots and hesitations can get annoying fast. Finally, I will be doing a four corner brake job (its very overdue) and I ended up going a different route for the front so the Z-06 front brakes (calipers, rotors, pads etc) w the adapter brackets I made will be up for sale. Not interested in making any money, just want to get even for what I paid for the components so if you know anyone interested, LMK. Cheers! Chris |
Thats the way to turbo charge a RX8. Nice job man
|
I've been following your post. Great build. i really mean great build. From a machinist/engineer to another, its good to see how creative we can be. Whenever I have my friend time, my build will be next. =)
|
1 Attachment(s)
^ Thanks man.
I figured I would post a recent engine bay pic with the ECU out of there and things looking a bit more organized...still have some loose ends to tie up but its slowly coming together. Cheers! Attachment 697833 |
Your 8 looks good man nice job ,
|
Have you dyno tuned it yet? Wondering how the midrange of the RE Cosmo is compared to the REW..
|
Originally Posted by 1FAASTFD3S
(Post 11244088)
Have you dyno tuned it yet? Wondering how the midrange of the RE Cosmo is compared to the REW..
I will probably switch ECU's over the winter and after the new one gets tuned I will take it to the Dyno and post it on here. Cheers! Chris |
8 Attachment(s)
I got my new bumper installed and finished...Autoexe SE-02 :)
Way better looking than the OEM fish mouth it had going...lol Now just need to install some grill or mesh in there so you can't see straight into behind the bumper. Cheers! Attachment 694597 Attachment 694598 Attachment 694599 Attachment 694600 Attachment 694601 Attachment 694602 Attachment 694603 Attachment 694604 In case you wonder what it looks like since mine is black: http://www.bulletproofautomotive.com/items/ae00.jpg |
3 Attachment(s)
|
wow man just read through the thread loooks awesome, I'll send you a PM but i will ask here too, A while ago you where going to do the 20b and there was talk of a quick spool valve.
do you still have that valve? would you be willing to sale it? |
Dont hate im a women RX8 driver and i deff. know more than you give credit i have taken a half a dozen renesis motors apart and they are crap compared to the REW or RE the series 2 got alot better then series 1 but series 1 is what i have and it was a very poor design on mazdas part i felt they couldve done better with the design and shouldve kept the twin turbos !
Originally Posted by rcracer_tx
(Post 10994546)
Very good point on the average rx8 driver. There is a lot of women rx8 drivers around my area and they wouldn't even know that their car was rotary powered. Its irritating that Mazda took a major step backwards from rew to the reni in being able to make reliable power. Did you part out the reni setup?
|
Rotary chick I remember u wanting to do a swap, what happened?
|
I bought a 2nd gen and put the REW in there way easier and less money just keeping the 8 for daily driving might port it a bit but other than that im just leaving it alone.
Originally Posted by dznutzuk
(Post 11260581)
Rotary chick I remember u wanting to do a swap, what happened?
|
Slight update...car is away for winter and the long list of "leftover" To Do's is now in session.
Before putting it away I added LED's to the bumper, they look really good and do a good job of replacing the OME fog lights I lost in the bumper switch. They look blurry in the pics but in person you can really see the individual "dots" like on the Audi's. More updates coming soon! Chris [IMG]<a href="http://s679.beta.photobucket.com/user/gchdavid/media/13B-RE%20Conversion/20121026_170445.jpg.html" target="_blank"><img src="http://i679.photobucket.com/albums/vv155/gchdavid/13B-RE%20Conversion/20121026_170445.jpg" border="0" alt="Photobucket"/></a>[/IMG] http://s679.beta.photobucket.com/use...026_170540.jpg http://s679.beta.photobucket.com/use...026_170626.jpg http://s679.beta.photobucket.com/use...030_172446.jpg |
Originally Posted by rtrychk08
(Post 11262048)
... just keeping the 8 for daily driving might port it a bit but other than that im just leaving it alone.
|
this car is absolutely beautiful and the work appears quite stellar. i love it.
any photos of the Vette brakes mounted that you can share? |
Ooops...Pics didn't work.
Here goes the 2nd attempt! Cheers! [IMG]http://i679.photobucket.com/albums/v...026_170445.jpg[/IMG] [IMG]http://i679.photobucket.com/albums/v...026_170619.jpg[/IMG] [IMG]http://i679.photobucket.com/albums/v...026_170626.jpg[/IMG] [IMG]http://i679.photobucket.com/albums/v...030_172446.jpg[/IMG] |
Looking good and clean
|
Originally Posted by ChrisRX8PR
(Post 11338610)
|
Amazing thread. One of the most beautiful RX-8 I have seen! Well done.
|
Originally Posted by diabolical1
(Post 11342336)
so awesome i'm speechless. how does the car feel now compared to the stock units?
On another note, i will be getting rid of the Z06 front kit so if anypne wants to work on adapting it to their car LMK. Cheers! Chris |
that is one sexy rx8 bori
|
10 Attachment(s)
Quick update.
It became clear that my initial "idle bleed valve" for controlling working in conjunction with the OEM throttle wasn't adequate so I decided to adapt the BAC that came with my engine to the RX-8 throttle so that I could use the ECU to control idle properly. here are some pics of what I did. Cheers! Attachment 679379 Radiusing Attachment 679380 One hole at an angle (must come in behind butterfly plate) Attachment 679381 Attachment 679382 Attachment 679383 Attachment 679384 Attachment 679385 Attachment 679386 http://i679.photobucket.com/albums/v...ps0eb68585.jpg Attachment 679387 Attachment 679388 http://i679.photobucket.com/albums/v...ps9b2df49d.jpg |
Originally Posted by che'srx-7
(Post 11343506)
that is one sexy rx8 bori
|
amazing work.
|
Badass!
|
5 Attachment(s)
Quick update, I did my UIM and it looks great...I can't wait to put this back together with the engine bay all cleaned up.
Cheers! Attachment 679271 Attachment 679272 Attachment 679273 Attachment 679274 Attachment 679275 |
Amazing build! What type of finish is that on the upper manifold?
|
love the caliper brackets
|
Originally Posted by ArmyOfOne
(Post 11403918)
Amazing build! What type of finish is that on the upper manifold?
C |
gr8 build
|
built in boost leak tester?
|
Originally Posted by che'srx-7
(Post 11404804)
built in boost leak tester?
C |
All times are GMT -5. The time now is 06:07 PM. |
© 2024 MH Sub I, LLC dba Internet Brands