help me with my REPU
#1
www.discgolforegon.com
Thread Starter
iTrader: (4)
Join Date: Mar 2008
Location: tha burg
Posts: 385
Likes: 0
Received 0 Likes
on
0 Posts
help me with my REPU
im trying to get the dash pad and the metal part behind it off. i took the screws out of the top. and the ones under the front edge of the dash pad. but it doesn't even seem loose if anyone could help me out i would appreciate it. i just dont want to break anything as i know stuff is hard to find for these things.
thanks in advance
SOdrifter
thanks in advance
SOdrifter
#3
Senior Member
iTrader: (4)
Join Date: Dec 2004
Location: Rotary,California
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
repu dash
you have to take off the metal part ,and then the pad...
the metal parts has a few screws along the front windshield rubber , then you have to pop the rear part with a screw driver.....when you take off the metal you will see the screws holding the pad down, there is a 10mm nut on each of the corners where it curves,and there is a few push type fasteners, you have to take off the speedo to get to it......
here is a pic of my repu....
the metal parts has a few screws along the front windshield rubber , then you have to pop the rear part with a screw driver.....when you take off the metal you will see the screws holding the pad down, there is a 10mm nut on each of the corners where it curves,and there is a few push type fasteners, you have to take off the speedo to get to it......
here is a pic of my repu....
#5
www.discgolforegon.com
Thread Starter
iTrader: (4)
Join Date: Mar 2008
Location: tha burg
Posts: 385
Likes: 0
Received 0 Likes
on
0 Posts
sweet, thanks fellas
it was the screws at the base of the windshield i was overlooking.
my window is real dusty and i couldnt see them.
got it off now though
i'll post pics of my repu tomorrow. its not pretty, but its a find for 200$
awesome truck, HOOKS ROTARY
no offence but those WANKELHOLICS banners need to be curved slightly upward in the design. this will make them appear straight across the windshield.
i only say this because i do vinyl work on the side and have run into this problem
thanks again
it was the screws at the base of the windshield i was overlooking.
my window is real dusty and i couldnt see them.
got it off now though
i'll post pics of my repu tomorrow. its not pretty, but its a find for 200$
awesome truck, HOOKS ROTARY
no offence but those WANKELHOLICS banners need to be curved slightly upward in the design. this will make them appear straight across the windshield.
i only say this because i do vinyl work on the side and have run into this problem
thanks again
Trending Topics
#12
ol skool rotorhead
Join Date: Nov 2007
Location: san diego
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
sweet *** repu
Yup Wacky's right...thats about the sweetest repu in socal bro . Really well done, subtle with just the right mods and flash...luv it! Ol skool done right. Wheres the recent pics of Max's repu (maroon, super clean)? You and Hooks are holdin' it down for the completed repus...."big ups to both of you guys Tom G
#13
Senior Member
iTrader: (4)
Join Date: Dec 2004
Location: Rotary,California
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
repu
will give that a try Wacky.....do you know of any good paint for these new pos plates? ,since they have some kind of vinyl or plastic coat on it don't really know what kind of paint to use....
#14
Senior Member
iTrader: (4)
Join Date: Dec 2004
Location: Rotary,California
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
repu / RX2
Yup Wacky's right...thats about the sweetest repu in socal bro . Really well done, subtle with just the right mods and flash...luv it! Ol skool done right. Wheres the recent pics of Max's repu (maroon, super clean)? You and Hooks are holdin' it down for the completed repus...."big ups to both of you guys Tom G
#15
www.discgolforegon.com
Thread Starter
iTrader: (4)
Join Date: Mar 2008
Location: tha burg
Posts: 385
Likes: 0
Received 0 Likes
on
0 Posts
im trying to see if my old repu will run. it has sat for 10+ years. i didn't have spark and i got that fixed. new cap, rotor, points and condensors, plugs and taylor wires( i had the wires laying around) i dont have a way to test the compression but i took out the leading plugs and all the compression cycles sound strong and the same. i was told to pull it in second at about 25mph and see if it fires up that way.any suggestions would be greatly appreciated.
the old couple i bought it from told me they used to go to the dump with it about once a month. one day it died on the way back and so they parked and bought a new truck when i got it there was no spark and the points looked like ****.
im hoping this is why it quit.
this is the cleanest old motor i have ever seen. not a drop of oil leaking. and no greasy build up anywhere.
+ i want to ditch my air pump, what do i have to do to make it right? can i still use the stock carb. and exh. mani. or do i have to upgrade?
man your truck is clean HOOKS! i cant stop lookin at it.
the old couple i bought it from told me they used to go to the dump with it about once a month. one day it died on the way back and so they parked and bought a new truck when i got it there was no spark and the points looked like ****.
im hoping this is why it quit.
this is the cleanest old motor i have ever seen. not a drop of oil leaking. and no greasy build up anywhere.
+ i want to ditch my air pump, what do i have to do to make it right? can i still use the stock carb. and exh. mani. or do i have to upgrade?
man your truck is clean HOOKS! i cant stop lookin at it.
#16
Senior Member
iTrader: (4)
Join Date: Dec 2004
Location: Rotary,California
Posts: 321
Likes: 0
Received 0 Likes
on
0 Posts
thanks ,so drifter......
I say your best bet is trash that points dizzy and swap in a electronic dizzy out of a rx7 .....and yes you could pull it to try and pop start it ....
I say your best bet is trash that points dizzy and swap in a electronic dizzy out of a rx7 .....and yes you could pull it to try and pop start it ....
#18
Admitted 'rexaholic'
LISTEN to Drivefast and Hooks...getcha an 84/85 dizzy and slap in there, you won't be sorry. You'll have her running in no time. In case you need more info on those trucks check out MAZDAREPU.COM if you haven't already. Also, there's still carb rebuild kits to be had from napa if needed later.
#19
www.discgolforegon.com
Thread Starter
iTrader: (4)
Join Date: Mar 2008
Location: tha burg
Posts: 385
Likes: 0
Received 0 Likes
on
0 Posts
thanks a ton guys, i have checked out MAZDAREPU.COM. lots of good info there. i heard about the 1st gen distributor. but i just wasnt sure how beneficial it was.
so i guess when i get payed this week i will get that done.
im pretty sure the carb could use a rebuild after sitting for ten years. guess im gonna have to hit up napa too.
does anyone have the part # for the rebuild kit?
it would save me a ton of headache trying to explain to the lame parts guy what my truck is
so i guess when i get payed this week i will get that done.
im pretty sure the carb could use a rebuild after sitting for ten years. guess im gonna have to hit up napa too.
does anyone have the part # for the rebuild kit?
it would save me a ton of headache trying to explain to the lame parts guy what my truck is
#21
Admitted 'rexaholic'
That number should be on the mazdarepu site somewhere..I think that's where I found it. I also may have it written down in my book, if I do I'll post it up for ya.
I may order an extra, I'm betting they ain't making many more of those hitachi rebuild kits much longer.
Found it, the kit is CRB 21211, it's around $18. You'll also want to order CRB24117, the secondary throttle diaphragm, it's pretty cheap, as I remember, maybe $10. They've also got fuel filters, pumps, etc. Never used those, though. They seem to be they only source I know of that have a complete kit for our carbs. Nice sheet inside the box that shows the breakdown, too. You'll have fun. Watch those damn little bearings......
I may order an extra, I'm betting they ain't making many more of those hitachi rebuild kits much longer.
Found it, the kit is CRB 21211, it's around $18. You'll also want to order CRB24117, the secondary throttle diaphragm, it's pretty cheap, as I remember, maybe $10. They've also got fuel filters, pumps, etc. Never used those, though. They seem to be they only source I know of that have a complete kit for our carbs. Nice sheet inside the box that shows the breakdown, too. You'll have fun. Watch those damn little bearings......
Last edited by mwpayne; 08-02-08 at 08:44 AM.
#23
Full Member
iTrader: (1)
just rebuilt my carb
w/ a napa kit... not bad. if you've read other threads on this subject, can't stress how important it is to clean out everything. if you follow the instructions and set the floats correct (if they even needed adjusting), it should fire right up.
i was pleasantly surprised and it worked out really well.
i was pleasantly surprised and it worked out really well.
#25
www.discgolforegon.com
Thread Starter
iTrader: (4)
Join Date: Mar 2008
Location: tha burg
Posts: 385
Likes: 0
Received 0 Likes
on
0 Posts
well i decided to block off the air pump.
and im gonna put a holley on it and delete the OMP to run premix
it just seems easier
still need help with the dist. swap
what do i need as far as parts?
PLEASE HELP?
and im gonna put a holley on it and delete the OMP to run premix
it just seems easier
still need help with the dist. swap
what do i need as far as parts?
PLEASE HELP?