going old skool got a repu:)
05-23-09 | 10:33 PM
#53
Thread Starter
kiwi from downunder..
iTrader: (4)
Joined: Nov 2005
Posts: 3,423
Likes: 5
From: springfield,oregon
neither can i wacky
got the tranny mounted i managed to reuse the repu crossbar and rubber mount and modifyed it to fit worked out great
water pump hitting 1st gen cover
wp
[img][/img]
grinded
end result of todays work
got the tranny mounted i managed to reuse the repu crossbar and rubber mount and modifyed it to fit worked out great
water pump hitting 1st gen cover
wp
[img][/img]
grinded
end result of todays work
05-30-09 | 02:55 PM
#60
Thread Starter
kiwi from downunder..
iTrader: (4)
Joined: Nov 2005
Posts: 3,423
Likes: 5
From: springfield,oregon
test fitting manifold etc. i got a tb snorkle from a 87 n/a rx7 i had to knock the oil filler off for it to work so ill have to get it shortened to fit underneith.
06-08-09 | 12:20 AM
#62
Thread Starter
kiwi from downunder..
iTrader: (4)
Joined: Nov 2005
Posts: 3,423
Likes: 5
From: springfield,oregon
today i droped the tank to have a good look inside for rust.
got the new 3/8 hard lines in what a pain in the *** that was also got the pump installed.
overall pic
made some brackets to hook up my 1stgen oil cooler
go this chrome trim for my hood
got the new 3/8 hard lines in what a pain in the *** that was also got the pump installed.
overall pic
made some brackets to hook up my 1stgen oil cooler
go this chrome trim for my hood
good work man. You're getting there
06-14-09 | 02:46 AM
#67
Thread Starter
kiwi from downunder..
iTrader: (4)
Joined: Nov 2005
Posts: 3,423
Likes: 5
From: springfield,oregon
i have 99% of the ecu wireing done just have 2 12v wires and 1 switched wire to hook up.
also flared the 3/8 tubeing today and installed the tank. i bypassed the condesor tank for now need to pull it off clean it and maybe make a surge tank.
bolted the header up today found that i had to notch the tranny crossbar a little bit so it didnt contact.
cleaned the throttle body tonight and also fliped the acell linkage around so i could pull from the drivers side.
it turns out the linkage for the omp rod isnt on this tb i might have to premix for a while. anyone know the mixture for that?
not much left to do now im getting nervous lol.
also flared the 3/8 tubeing today and installed the tank. i bypassed the condesor tank for now need to pull it off clean it and maybe make a surge tank.
bolted the header up today found that i had to notch the tranny crossbar a little bit so it didnt contact.
cleaned the throttle body tonight and also fliped the acell linkage around so i could pull from the drivers side.
it turns out the linkage for the omp rod isnt on this tb i might have to premix for a while. anyone know the mixture for that?
not much left to do now im getting nervous lol.
06-29-09 | 12:14 AM
#70
I think the premix for 2 cycle oil is 2oz per 10 gallons of gas. I know CodeBlue (look him up in the members list) uses premix he can tell you. He is under the same name in the nopistons forum too if you don't get an answer here.
06-29-09 | 10:42 AM
#73
Thread Starter
kiwi from downunder..
iTrader: (4)
Joined: Nov 2005
Posts: 3,423
Likes: 5
From: springfield,oregon
i found that people were mixing 1 oz to a gallon so i did that.
iv got the truck started and it idels for 5seconds looks like i have major vaccum leaks as wells as the engine keeps flooding so ill send the injectors out for cleaning.
camt wait to take this truck for a spin,.
iv got the truck started and it idels for 5seconds looks like i have major vaccum leaks as wells as the engine keeps flooding so ill send the injectors out for cleaning.
camt wait to take this truck for a spin,.
