Portland DEQ
#1
Thread Starter
Banned. I got OWNED!!!
iTrader: (7)
Joined: Dec 2008
Posts: 1,326
Likes: 0
From: Oregon
Portland DEQ
I'm getting my T2 in the next few days. It needs a new wiring harness to pass DEQ is what I've been told by the PO. Do they do a sniff test on older (1987) cars, or do they plug me in. I think it should pass the sniff test if I do a tune up on her. other than that the car runs drives great. is there ways to help me cheat also. I know derekcat has used MMO or sea foam to help get him through, would this be bad for a T2. I ask because I know you have to be careful to run premium gas to prevent detonation, and wouldn't sea foam drop down the octane?
#4
Not mmo or seafoam... Isoheet [denatured alcohol].
You should go read in the second gen tech section to find out if the same steps apply for T][s and NAs..
On my NAs I need to do this: working cat+air pump output to the split air pipe [the pipe coming from the cat to the exhaust side of the engine bay]+ 1/8th tank of gas+2 bottles of Isoheet in the tank+fill up with normal gas IMMEDIATELY after the test+Disconnect the airpump output from the split air pipe when you're filling up after the test.
and that makes it pass with flying colors.. I remember reading that you need to drive very gingerly while running this setup [do not rev up/use much throttle]
To be clear: I HAVE NO IDEA IF THIS IS, OR IS NOT SAFE FOR TURBO ROTARIES.
You should go read in the second gen tech section to find out if the same steps apply for T][s and NAs..
On my NAs I need to do this: working cat+air pump output to the split air pipe [the pipe coming from the cat to the exhaust side of the engine bay]+ 1/8th tank of gas+2 bottles of Isoheet in the tank+fill up with normal gas IMMEDIATELY after the test+Disconnect the airpump output from the split air pipe when you're filling up after the test.
and that makes it pass with flying colors.. I remember reading that you need to drive very gingerly while running this setup [do not rev up/use much throttle]
To be clear: I HAVE NO IDEA IF THIS IS, OR IS NOT SAFE FOR TURBO ROTARIES.
#6
Thread Starter
Banned. I got OWNED!!!
iTrader: (7)
Joined: Dec 2008
Posts: 1,326
Likes: 0
From: Oregon
alright thanks guys. I'll check the 2nd gen section.
Edit: Just searched the 2nd gen section using terms ISOheet, ISO heet. found 4 threads none touched on the topic of Turbo Apps. So if anybody knows let me know.
Mark, you said you use it to pass, have you tryed it on a T2 or your FD's?
Edit: Just searched the 2nd gen section using terms ISOheet, ISO heet. found 4 threads none touched on the topic of Turbo Apps. So if anybody knows let me know.
Mark, you said you use it to pass, have you tryed it on a T2 or your FD's?
Trending Topics
#8
Thread Starter
Banned. I got OWNED!!!
iTrader: (7)
Joined: Dec 2008
Posts: 1,326
Likes: 0
From: Oregon
Ok, would it be safe to create a boost leak with a CAI bypass filter placed before the intercooler, then run the ISOHeet? Would this keep it from boosting?
This is what I'm talking about
http://cgi.ebay.com/ebaymotors/NEW-2...item3a52b38dc0
This is what I'm talking about
http://cgi.ebay.com/ebaymotors/NEW-2...item3a52b38dc0
Thread
Thread Starter
Forum
Replies
Last Post
gabescanlon
3rd Generation Specific (1993-2002)
2
09-15-15 06:57 AM