88 Vert Turbo II swap
#1
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
88 Vert Turbo II swap
I have an N/A 88 Vert. I just picked up a new Turbo II motor and everything. And I want to know if I can use my original Trans? and what other small stuff I need?
#2
Top Down, Boost Up
iTrader: (7)
Now would be a good time to read through the FAQ: https://www.rx7club.com/showthread.p...55#post5131155.
Can I swap a Turbo engine/Jspec engine/13BT/etc into my Non Turbo?
Yes, check these links:
https://www.rx7club.com/2nd-gen-archive-72/s4-na-turbo-swap-details-813825/
http://www.rotaryresurrection.com/2n...o_s4_swap.html
http://www.rotaryresurrection.com/2n...o_s5_swap.html
Yes, check these links:
https://www.rx7club.com/2nd-gen-archive-72/s4-na-turbo-swap-details-813825/
http://www.rotaryresurrection.com/2n...o_s4_swap.html
http://www.rotaryresurrection.com/2n...o_s5_swap.html
Last edited by RotaryRocket88; 01-02-11 at 11:33 PM.
#3
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 110 Likes
on
93 Posts
To answer the transmission question, sort of....If you don't intend on upgrading the engine much and keep the power level around 200HP, then it should be fine for a while. The NA transmission is far weaker than the TII transmission and while it will handle the power (and surprisingly, a lot more power) it also becomes FAR easier to break.
If you want to use the NA transmission, you'll need to swap the NA flywheel onto the turbo engine.
If you want to use the NA transmission, you'll need to swap the NA flywheel onto the turbo engine.
#4
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Ok Cause I dont really plan on doing a whole lot to the motor. Mainly just wanted it as a daily driver for now. Cause My issue was I could not find a T II rear end.
#6
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Finally got started with the swap, the engine is out and I am cleaning up under the Hood, also put on a newer top, s5 tails, and I am looking for an exhaust....any ideas? I want to keep the dual style system,
#7
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Here Is basically what it looked like when I got it, Sat for years in a Field, But Put a Battery in it and it started right up.. the Original Engine actually runs really well...But Its gone and now time for the TII
Trending Topics
#14
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Man, Yeah its coming along the entire car now is primer black, and i figured now is the best time as any to tear it apart...hopefully it will be running again in the next week or so...Now if the weather would work for me...
#16
Brap Brap Brap
iTrader: (3)
Join Date: Jan 2010
Location: Pennsylvania
Posts: 981
Likes: 0
Received 0 Likes
on
0 Posts
No problem. Yeah summer is a great time to work on your 7, I was stuck favoring one of my 7s over the other but Im focused on my vert now. It looks like you have a cool project going on though, itll be awesome when its done. For emissions removal go to rotaryresurrection.com and look in the tech section and it will have a good write up with pictures on what to remove and how to!
#22
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Picked up the Wheels off Craigslist. I wanted a set of staggered 17's. But found these for only $200! So 18's it is. The Tires are shot and they are little beat up and one of the fronts has a a pretty bad rash...but I am going to see if I can clean them up a bit.
Last edited by gsl-se addict; 02-06-12 at 01:32 PM. Reason: pic layout
#23
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Whats the difference between the n333 and n332? I previously bought the n333 for the swap, but I picked up another harness and the guy threw in the n332.
#24
Top Down, Boost Up
iTrader: (7)
N332: '87 TII
N333: '88 TII or 10AE
They're interchangeable. https://www.rx7club.com/2nd-gen-archive-72/ecu-part-numbers-applications-873382/
N333: '88 TII or 10AE
They're interchangeable. https://www.rx7club.com/2nd-gen-archive-72/ecu-part-numbers-applications-873382/
#25
Full Member
Thread Starter
Join Date: Apr 2008
Location: Matthews NC
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
N332: '87 TII
N333: '88 TII or 10AE
They're interchangeable. https://www.rx7club.com/showthread.php?t=873382
N333: '88 TII or 10AE
They're interchangeable. https://www.rx7club.com/showthread.php?t=873382