Maryland guys!
Well been working my butt off on this car. The water pump started leaking so i had to address that. Had some issues with the pulley not being pressed in far enough on the new one so i had to ship back. Too make a long story short i ended up with new w/p and radiator. Been all through the enginge pretty much, my omp was leaking and I found the top bolt was broke. So i said f it and blocked it off. Then just deleted my pd with the banjo bolt till i get a new one. Which might lead to my next possible problem of finding a little bit of fuel traces in my dynamic chamber. So yesterday was pretty much the first time i started it. Idle was off and threw my for a loop till late last night when i remembered the thermowax was sticking before. So i fixed it temporarily lol i know lots of temporary fixes but hey cant afford everything at once. After all that and some my idle is back close enough for me to leave it be for now. And the tps is set now only by volts but the car ran great. I still do get a little hang up on my idle, sometimes it just sits a little high at idle than it should. If i let the clutch out a little it comes right down to 750-800. Might still have a vac leak somewhere idk. So after all this I have to buy springs and get them my shocks n engine mount put on. Then recheck and fix tranny mount if Its not good. I think the bushing is gone on it. Might just put a hockey puck in there lol. So yeah thats my life lol
F'n Newbie...
iTrader: (6)
Well been working my butt off on this car. The water pump started leaking so i had to address that. Had some issues with the pulley not being pressed in far enough on the new one so i had to ship back. Too make a long story short i ended up with new w/p and radiator. Been all through the enginge pretty much, my omp was leaking and I found the top bolt was broke. So i said f it and blocked it off. Then just deleted my pd with the banjo bolt till i get a new one. Which might lead to my next possible problem of finding a little bit of fuel traces in my dynamic chamber. So yesterday was pretty much the first time i started it. Idle was off and threw my for a loop till late last night when i remembered the thermowax was sticking before. So i fixed it temporarily lol i know lots of temporary fixes but hey cant afford everything at once. After all that and some my idle is back close enough for me to leave it be for now. And the tps is set now only by volts but the car ran great. I still do get a little hang up on my idle, sometimes it just sits a little high at idle than it should. If i let the clutch out a little it comes right down to 750-800. Might still have a vac leak somewhere idk. So after all this I have to buy springs and get them my shocks n engine mount put on. Then recheck and fix tranny mount if Its not good. I think the bushing is gone on it. Might just put a hockey puck in there lol. So yeah thats my life lol
If you need a hoist or a stand (if you plan on pulling the motor/trans for the tranny mount) let me know, as I've got both at mine in Odenton.
Stoned
iTrader: (3)
That blows. Really wanted to try that place. Roadtrip to DE xD
Apexsealistically Chalngd
iTrader: (4)
Senior Member
iTrader: (2)
With that said, I am going to set a meet, like the old ones:
Sunday, August 30, 2015. 12:00pm.
Fuddruckers
6486 Dobbin Rd
Columbia, MD 21045
(
I'll be there sometime around 11am, and hang in the back parking lot. Plan on eating around noon. If no one else shows up, oh well. This will be posted in your other thread as well:
https://www.rx7club.com/ne-rx-7-foru...-meet-1087334/
Last edited by wesmcbride; 08-18-15 at 02:20 PM.
Apexsealistically Chalngd
iTrader: (4)
These are just my thoughts. The lack of interest is due to nothing actually being set. Also, I didn't realize you posted a new thread. I rarely come to these threads and only read the updates in my email.
With that said, I am going to set a meet, like the old ones:
Sunday, August 30, 2015. 12:00pm.
Fuddruckers
6486 Dobbin Rd
Columbia, MD 21045
(map)
I'll be there sometime around 11am, and hang in the back parking lot. Plan on eating around noon. If no one else shows up, oh well. This will be posted in your other thread as well:
https://www.rx7club.com/ne-rx-7-foru...-meet-1087334/
With that said, I am going to set a meet, like the old ones:
Sunday, August 30, 2015. 12:00pm.
Fuddruckers
6486 Dobbin Rd
Columbia, MD 21045
(map)
I'll be there sometime around 11am, and hang in the back parking lot. Plan on eating around noon. If no one else shows up, oh well. This will be posted in your other thread as well:
https://www.rx7club.com/ne-rx-7-foru...-meet-1087334/
Doritos & Dual Sports
iTrader: (8)
Well my 85 is in th middle of a Frankenstein 13b swap and the gf's 79 limited doesn't have functional rear calipers. They're ordered and I'm picking up some useable ones earlier Sunday morning in Frederick, hopefully either the new ones come in or I get back in time to put the calipers on and head up. If nothing else ill drive to daily up so I can at least meet some MD rx7 folk.
Doritos & Dual Sports
iTrader: (8)
got my left caliper in yesterday just waiting on righty! see you all sunday
Apexsealistically Chalngd
iTrader: (4)
[QUOTE=eage8;11961656]My car didn't break at today's autocross so I'll be there
I'm in Eldersburg if you want to meet up to drive down there.
I'm in Eldersburg if you want to meet up to drive down there.
Senior Member
iTrader: (2)
Senior Member
Join Date: Sep 2008
Location: Glen Burnie, Maryland
Posts: 543
Likes: 0
Received 0 Likes
on
0 Posts
These are just my thoughts. The lack of interest is due to nothing actually being set. Also, I didn't realize you posted a new thread. I rarely come to these threads and only read the updates in my email.
With that said, I am going to set a meet, like the old ones:
Sunday, August 30, 2015. 12:00pm.
Fuddruckers
6486 Dobbin Rd
Columbia, MD 21045
(map)
I'll be there sometime around 11am, and hang in the back parking lot. Plan on eating around noon. If no one else shows up, oh well. This will be posted in your other thread as well:
https://www.rx7club.com/ne-rx-7-foru...-meet-1087334/
With that said, I am going to set a meet, like the old ones:
Sunday, August 30, 2015. 12:00pm.
Fuddruckers
6486 Dobbin Rd
Columbia, MD 21045
(map)
I'll be there sometime around 11am, and hang in the back parking lot. Plan on eating around noon. If no one else shows up, oh well. This will be posted in your other thread as well:
https://www.rx7club.com/ne-rx-7-foru...-meet-1087334/
Well ****, If only i kept up with my yahoo email I would have swung by. Havnt had a rotary in like 4 years now but hey it is what it is. And if i had extra moneys set aside I would get myself back in one