Maryland guys!
#6551
Attack Gas Station!!!!
Join Date: May 2004
Location: Catonsville, Maryland
Posts: 1,081
Likes: 0
Received 0 Likes
on
0 Posts
ken, could you give me a quick rundown on the connections for the lm1815 please. I'll be putting it together this afternoon. Oh, and I think I've figured out a solution for the extra db-9... use a 7-pin s-video cable instead.
#6552
MegaSquirt Mod
Originally Posted by sudseh
ken, could you give me a quick rundown on the connections for the lm1815 please. I'll be putting it together this afternoon. Oh, and I think I've figured out a solution for the extra db-9... use a 7-pin s-video cable instead.
it'll have to wait till I get home tonight... I don't have time to look at it before that....
That's the stuff I drilled a couple of small holes in the MS board for.... remember?
If you still don't, take a look at my .txt file at http://www.speakeasy.org/~culverk/wh...oder-howto.txt
I need to go back and edit this thing eventually... but it should be OK until then.
Last edited by muythaibxr; 07-08-05 at 01:24 PM.
#6553
Attack Gas Station!!!!
Join Date: May 2004
Location: Catonsville, Maryland
Posts: 1,081
Likes: 0
Received 0 Likes
on
0 Posts
yah >_> I remember that there were the 2 signal wires and 2 grounds from the cas (vr1,gnd1,vr2,gnd2) and that output1 goes to pin6 on the 6-pin chip, but I don't remember from there.
*dloads file* If I need any more hints I'll talk to you when you get home.
oh, and I'm going to use an 8-pin appletalk cable for the connections.
*dloads file* If I need any more hints I'll talk to you when you get home.
oh, and I'm going to use an 8-pin appletalk cable for the connections.
#6554
Senior Member
Join Date: Oct 2004
Location: Baltimore
Posts: 686
Likes: 0
Received 0 Likes
on
0 Posts
hey guys and gals...
stilllookin for info on rekeying JUST the ignition cylinder on an FC.. just need the tumbler and the key ... i can do the install myself
anyone know where i can get one and about how much it will run me?
stilllookin for info on rekeying JUST the ignition cylinder on an FC.. just need the tumbler and the key ... i can do the install myself
anyone know where i can get one and about how much it will run me?
#6555
Senior Member
Join Date: Oct 2004
Location: Baltimore
Posts: 686
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by muythaibxr
Actually no, if the aluminum is thick enough, you can mig weld it too... I did it in my welding class... it's very easy in fact, and the welds turn out strong too.
If the metal is thin then yes, you need to tig weld it, mainly just to get the really fine control of the current to keep from burning through the metal.
If the metal is thin then yes, you need to tig weld it, mainly just to get the really fine control of the current to keep from burning through the metal.
i mean i may be way off base...but arent oil coolers finned radiators basically
i mean thats thin to me
i've never MIG welded aluminum so i can say ... but very few people would have a MIG that can do Al welds and make them look nice...
you need an adjustable waveform and reverse polarity if im not mistaken
better safe than sorry, most good shops have a TIG anyways
try RPM Fabrication LLC in Glen Burnie, ask for Harry, tell him Corey, the guy with the v8 rx7 sent ya
#6556
Jesus is the Messiah
¡Hola!
I´m in the Dominican Republic, we came into town (a crazy drive down the mountain, for supplies), so I paid for some internet time. These spanish keybords are crazy. The poverty here is aweful, I´m serving in a town called Polo, right neer the border of Hati, high in the mountains.
There is a whole lot of hard labor to be done here too to help administer aid and such to the people living here. Biulding this house is kinda hard too, because we dont have powertools or anything like that. Lots of digging by hand and such. Money is really tight too. everything here is really expensive. (Exept labor)
One of the trucks we are using is awesome, it´s called a Toyota Dyna. It rules.
I´ll tell everyone the full story later, at Fudds or something, I just thought it would be cool to post and let everyone know that I am still alive.
I´m in the Dominican Republic, we came into town (a crazy drive down the mountain, for supplies), so I paid for some internet time. These spanish keybords are crazy. The poverty here is aweful, I´m serving in a town called Polo, right neer the border of Hati, high in the mountains.
There is a whole lot of hard labor to be done here too to help administer aid and such to the people living here. Biulding this house is kinda hard too, because we dont have powertools or anything like that. Lots of digging by hand and such. Money is really tight too. everything here is really expensive. (Exept labor)
One of the trucks we are using is awesome, it´s called a Toyota Dyna. It rules.
I´ll tell everyone the full story later, at Fudds or something, I just thought it would be cool to post and let everyone know that I am still alive.
#6557
MegaSquirt Mod
Originally Posted by krautrocket
i mean i may be way off base...but arent oil coolers finned radiators basically
i mean thats thin to me
i've never MIG welded aluminum so i can say ... but very few people would have a MIG that can do Al welds and make them look nice...
you need an adjustable waveform and reverse polarity if im not mistaken
better safe than sorry, most good shops have a TIG anyways
try RPM Fabrication LLC in Glen Burnie, ask for Harry, tell him Corey, the guy with the v8 rx7 sent ya
i mean thats thin to me
i've never MIG welded aluminum so i can say ... but very few people would have a MIG that can do Al welds and make them look nice...
you need an adjustable waveform and reverse polarity if im not mistaken
better safe than sorry, most good shops have a TIG anyways
try RPM Fabrication LLC in Glen Burnie, ask for Harry, tell him Corey, the guy with the v8 rx7 sent ya
I don't remember what DCRP is used for really, I never used it for anything in class... I'll have to look it up in my textbook
for MIG all you need is the proper voltage, proper wire-feed speed, and proper wire-feed system; the spool-gun type works well...
I was just trying to tell people that it's NOT impossible to MIG aluminum, nor is it hard to make it look good.... as long as the metal is thick... a lot of people say that you can't MIG aluminum at all, and that just isn't true. You CAN MIG aluminum, and you CAN make it look good... there might even be people who can do it on thin metal, but I'm not one of them
Last edited by muythaibxr; 07-08-05 at 03:55 PM.
#6558
Beat Ninja
Originally Posted by Tofuball
¡Hola!
I´m in the Dominican Republic, we came into town (a crazy drive down the mountain, for supplies), so I paid for some internet time. These spanish keybords are crazy. The poverty here is aweful, I´m serving in a town called Polo, right neer the border of Hati, high in the mountains.
There is a whole lot of hard labor to be done here too to help administer aid and such to the people living here. Biulding this house is kinda hard too, because we dont have powertools or anything like that. Lots of digging by hand and such. Money is really tight too. everything here is really expensive. (Exept labor)
One of the trucks we are using is awesome, it´s called a Toyota Dyna. It rules.
I´ll tell everyone the full story later, at Fudds or something, I just thought it would be cool to post and let everyone know that I am still alive.
I´m in the Dominican Republic, we came into town (a crazy drive down the mountain, for supplies), so I paid for some internet time. These spanish keybords are crazy. The poverty here is aweful, I´m serving in a town called Polo, right neer the border of Hati, high in the mountains.
There is a whole lot of hard labor to be done here too to help administer aid and such to the people living here. Biulding this house is kinda hard too, because we dont have powertools or anything like that. Lots of digging by hand and such. Money is really tight too. everything here is really expensive. (Exept labor)
One of the trucks we are using is awesome, it´s called a Toyota Dyna. It rules.
I´ll tell everyone the full story later, at Fudds or something, I just thought it would be cool to post and let everyone know that I am still alive.
#6560
glass half empty, chug!
Join Date: Mar 2003
Location: Maryland
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by f1blueRx7
murderation of the pedestriation across the nation.
*note to self = werk on aim*
One speeding, failure to have registration in car, failure to display valid tags, driving a un insured car.
The cop decided to *** rape me. But the good news is that I got a new court date for it, so I can argue that some of them are bogus and that the cop did by no means have to write ALL this **** up for one account of which I was very cooperative and was completely un aware *cough* that my temp tags had expired.
#6561
Attack Gas Station!!!!
Join Date: May 2004
Location: Catonsville, Maryland
Posts: 1,081
Likes: 0
Received 0 Likes
on
0 Posts
ken: I just finished my megasquirt, lemme know when I can come over to fully benchtest it.
(I need to remove the jumpers and mount the crystal properly still)
(I need to remove the jumpers and mount the crystal properly still)
#6562
Senior Member
Join Date: Oct 2004
Location: Baltimore
Posts: 686
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by muythaibxr
the adjustable waveform and reverse polarity is still TIG... Most people use AC when TIG welding aluminum... the adjustable waveform is good for things like out of position welding on just about any metal... it helps avoid things like undercut by periodically reducing the current... allowing the metal to freeze... it's one of the things that helps get that "stacked dimes" look.
I don't remember what DCRP is used for really, I never used it for anything in class... I'll have to look it up in my textbook
for MIG all you need is the proper voltage, proper wire-feed speed, and proper wire-feed system; the spool-gun type works well...
I was just trying to tell people that it's NOT impossible to MIG aluminum, nor is it hard to make it look good.... as long as the metal is thick... a lot of people say that you can't MIG aluminum at all, and that just isn't true. You CAN MIG aluminum, and you CAN make it look good... there might even be people who can do it on thin metal, but I'm not one of them
I don't remember what DCRP is used for really, I never used it for anything in class... I'll have to look it up in my textbook
for MIG all you need is the proper voltage, proper wire-feed speed, and proper wire-feed system; the spool-gun type works well...
I was just trying to tell people that it's NOT impossible to MIG aluminum, nor is it hard to make it look good.... as long as the metal is thick... a lot of people say that you can't MIG aluminum at all, and that just isn't true. You CAN MIG aluminum, and you CAN make it look good... there might even be people who can do it on thin metal, but I'm not one of them
#6563
1308ccs of awesome
iTrader: (9)
Originally Posted by sudseh
ken: I just finished my megasquirt, lemme know when I can come over to fully benchtest it.
(I need to remove the jumpers and mount the crystal properly still)
(I need to remove the jumpers and mount the crystal properly still)
(sorry... It's a little early... and I have to work on a saturday )
#6564
MegaSquirt Mod
Originally Posted by krautrocket
and i dont want people to think i was saying you CANT ...MIG weld Al ... I myself have done it ... but not on something like an oil cooler which is definitely thin AL... better safe than sorry i always say
I was just saying that a lot of people say it's impossible to mig weld aluminum, and that's nothing more than a myth.
#6565
MegaSquirt Mod
Originally Posted by sudseh
ken: I just finished my megasquirt, lemme know when I can come over to fully benchtest it.
(I need to remove the jumpers and mount the crystal properly still)
(I need to remove the jumpers and mount the crystal properly still)
#6566
Beat Ninja
Originally Posted by Icesickkle
One speeding, failure to have registration in car, failure to display valid tags, driving a un insured car.
The cop decided to *** rape me. But the good news is that I got a new court date for it, so I can argue that some of them are bogus and that the cop did by no means have to write ALL this **** up for one account of which I was very cooperative and was completely un aware *cough* that my temp tags had expired.
The cop decided to *** rape me. But the good news is that I got a new court date for it, so I can argue that some of them are bogus and that the cop did by no means have to write ALL this **** up for one account of which I was very cooperative and was completely un aware *cough* that my temp tags had expired.
lol
#6567
Attack Gas Station!!!!
Join Date: May 2004
Location: Catonsville, Maryland
Posts: 1,081
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by muythaibxr
Leave the jumpers there for now... we can test with them in... Sunday afternoon/evening should be ok... but I have to work early on monday so you can't stay that late.
#6568
MegaSquirt Mod
Originally Posted by DarkAngelKamui
Huh, now why does that sound familiar?....
lol
lol
I'm still dealing with that PBJ though... for a stupid "I made a right turn between the hrs of 6:30 and 9:30 when a sign said not to...."
#6569
1308ccs of awesome
iTrader: (9)
I have a court date on thursday (63 in a 45)
and I think my lisence is actually suspended at the moment
(I forgot to pay a dumb ticket I got for not having my front lisence plate)
EDIT: I haven't been accused of a speeding ticket in over 2 years though... so I should be good... maybe
and I think my lisence is actually suspended at the moment
(I forgot to pay a dumb ticket I got for not having my front lisence plate)
EDIT: I haven't been accused of a speeding ticket in over 2 years though... so I should be good... maybe
#6570
glass half empty, chug!
Join Date: Mar 2003
Location: Maryland
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
Best of luck to you. I have a court date that I"m actually looking forward to on tuesday. I"m looking forward to it because the court is in OC ;-)
I'm making a day trip outa it!
I'm making a day trip outa it!
#6572
Right near Malloy
iTrader: (28)
Join Date: Dec 1999
Location: Behind a workbench, repairing FC Electronics.
Posts: 7,847
Received 513 Likes
on
348 Posts
Originally Posted by DarkAngelKamui
I've got Jury Duty on the 12th.... >_<
Wonder if there's a way I can skip it....
Wonder if there's a way I can skip it....
Hey. When they take you outta work in trade for $40 a day, are you really paid enough to give a ****?
#6575
"I've got Jury Duty on the 12th.... >_<
Wonder if there's a way I can skip it...."
yeah when you go their start talking crazy and saying things like guilty as charged 90 days in the slammer for you, Next. Oh yeah and laugh outloud alot and make references to your time in jail
Wonder if there's a way I can skip it...."
yeah when you go their start talking crazy and saying things like guilty as charged 90 days in the slammer for you, Next. Oh yeah and laugh outloud alot and make references to your time in jail