JPR Imports, South Jersey
11-15-06 | 02:29 PM
#26
Senior Member
Joined: May 2001
Posts: 395
Likes: 0
From: Baltimore, Maryland USA
Jim is most importantly one of the most honest guys in the business. I was lucky enough to include Jim in our R&D last year with the 13b. He was def a big help in getting our car to run the times it did.
I will be there for the grand opening tuning cars. I will also be speaking about the technology that went into the engine and the car itself to include turbo sizing, tuning etc etc that ran 7.49.
I plan on bringing all the data logs from the D200 logger putting the up on an overhead and going thru the data step by step.
Look forward to attending!!!
http://www.reactiveracing.com
I will be there for the grand opening tuning cars. I will also be speaking about the technology that went into the engine and the car itself to include turbo sizing, tuning etc etc that ran 7.49.
I plan on bringing all the data logs from the D200 logger putting the up on an overhead and going thru the data step by step.
Look forward to attending!!!
http://www.reactiveracing.com
Last edited by rotor_dee; 11-15-06 at 02:29 PM. Reason: spelling
11-15-06 | 04:57 PM
#27
Full Member
Joined: Oct 2005
Posts: 162
Likes: 0
From: pittsburgh
If I drive 5 hours to join the party, will you fine tune my car for free, lol. It was tuned by Steve Kan in August but it's running btw 11 and 12 at idle/low loads. It's between 10 and 11 under boost, so that's fine. :P
11-15-06 | 05:38 PM
#28
Rotary Enthusiast
Joined: May 2006
Posts: 1,406
Likes: 1
From: Ambler,PA
Originally Posted by magnus.rx7
If I drive 5 hours to join the party, will you fine tune my car for free, lol. It was tuned by Steve Kan in August but it's running btw 11 and 12 at idle/low loads. It's between 10 and 11 under boost, so that's fine. :P
Can we get you a hooker and some lobster too?
11-16-06 | 07:03 AM
#31
Newb Photog
Joined: Jul 2001
Posts: 2,171
Likes: 0
From: new jersey
Originally Posted by APEXL8T
Wow him and ITO in South Jersey. You guys must be rotary fanatics.The whole state takes two hours to cross and it takes 45 minutes just to cross my county.
11-16-06 | 08:55 AM
#32
Joined: Mar 2001
Posts: 30,575
Likes: 564
From: FL-->NJ/NYC again!
Originally Posted by wptrx7
Ito works at this shop as well? Anyone know how to get in contact with him?
Check this thread, if you need to get in touch with him you can always PM him:
https://www.rx7club.com/old-school-other-rotary-63/my-rx3-sp-dyno-310-rwhp-597047/
11-16-06 | 09:38 AM
#33
Wow this Sunday’s going to be amazing. there’s going to be prize give always, raffles, performance parts, and a Rotary swap meet. LOL
I hear parking is a bit of an issue @ the new shop…
Since i decided to break 2 studs instead of making progress on my ssm yesterday ill be there non-rotary
I hear parking is a bit of an issue @ the new shop…
Since i decided to break 2 studs instead of making progress on my ssm yesterday ill be there non-rotary
11-16-06 | 02:34 PM
#37
Rotary Enthusiast
Joined: Jul 2001
Posts: 1,320
Likes: 1
From: Santurce
Originally Posted by Bacon
Wow this Sunday’s going to be amazing. there’s going to be prize give always, raffles, performance parts, and a Rotary swap meet. LOL
I hear parking is a bit of an issue @ the new shop…
Since i decided to break 2 studs instead of making progress on my ssm yesterday ill be there non-rotary
I hear parking is a bit of an issue @ the new shop…
Since i decided to break 2 studs instead of making progress on my ssm yesterday ill be there non-rotary
11-19-06 | 08:11 PM
#43
Just wanted to spend a special thanks out to JIM , and DEE for today. Tremendous knowledge about the things many of us wouldn’t even think about. (But need to know to go real fast)
Also just wanted to congratulate JIM on a tremendous new shop, with tons of new possibilities ( a 2nd lift and a helper HINT HINT)
Definitely great to see everyone, wish I could have been there in a rotary.
Also just wanted to congratulate JIM on a tremendous new shop, with tons of new possibilities ( a 2nd lift and a helper HINT HINT)
Definitely great to see everyone, wish I could have been there in a rotary.
11-19-06 | 08:26 PM
#44
JPR IMPORTS.COM
Joined: Dec 2002
Posts: 43
Likes: 0
From: South Jersey
I want to thank everyone for coming out today.Special thanks to Joe for getting everything together,and dee for his support and tuning,and the guys from queens.Thank you all!!!! .....Jim...JPRIMPORTS.COM (thanks to you too mr bacon "JPR")
11-20-06 | 09:02 PM
#48
Rotary Enthusiast
Joined: May 2006
Posts: 1,406
Likes: 1
From: Ambler,PA
Originally Posted by Jay7 Nyc
Damn wish I knew about this get together. Next time can someone make a thread about the next meeting in a more detailed subject topic line...
Check out the Topic line PA NJ DEL MEET BEFORE IT GETS TO COLD. LOOK CLOSER
11-20-06 | 09:03 PM
#49
Rotary Enthusiast
Joined: May 2006
Posts: 1,406
Likes: 1
From: Ambler,PA
Originally Posted by Jay7 Nyc
Damn wish I knew about this get together. Next time can someone make a thread about the next meeting in a more detailed subject topic line...
Thread
Thread Starter
Forum
Replies
Last Post
