Hampton Roads (SE Virginia) Rotary Club
02-13-05, 06:16 AM
#1702
Senior Member
Join Date: Sep 2001
Location: Carrollton, VA
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by lovintha7
My brand new clutch is a turd. I was shifting around 8k last night, and all it would do was slip for a few seconds, then finally grab. Think I'm pushing too much hp for the stocker clutch. What clutches should I look at. Specifically, I was thinking Centerforce, or RB. What you guys think?
I just have a stock pressure plate, and a 'high-performance' disc from i think mazdatrix. i have no slipping problems.
dale
02-13-05, 08:16 PM
#1704
Rotary Freak
Thread Starter
Join Date: Sep 2001
Location: VA
Posts: 1,542
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by renagade_rotary
its startin to look like ill be without an rx7 this comming meet
02-14-05, 10:27 PM
#1706
Suicidal Death Missile
Join Date: Mar 2004
Location: Newport News, Virginia
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by phooka
slipping? for your 7? what have you done to the engine?
I just have a stock pressure plate, and a 'high-performance' disc from i think mazdatrix. i have no slipping problems.
dale
I just have a stock pressure plate, and a 'high-performance' disc from i think mazdatrix. i have no slipping problems.
dale
Street Port, RB Street Port exhaust, and RB Street port Holley setup.
BTW, My Sterling has been ordered and paid for, as well as a core turned in. Now All I have to do its wait for it, then port the intake when it comes in.
02-15-05, 05:37 PM
#1708
Senior Member
Join Date: Sep 2001
Location: Carrollton, VA
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by renagade_rotary
is there a super charger for the 12 a ?
http://www.camdensuperchargers.com/
02-16-05, 11:47 AM
#1709
Rotary Freak
Thread Starter
Join Date: Sep 2001
Location: VA
Posts: 1,542
Likes: 0
Received 0 Likes
on
0 Posts
Hey, everyone, don't forget about the meet this Saturday. This is our first in a while on the Penninsula. Here are the details:
When: Saturday, February 19, 2005 at 6:30 PM
Where: Hooter's
12640 Jefferson Avenue
Newport News, VA 23602
(757) 886-9464
If you aren't sure of the location go to mapquest.com and enter the address to get driving directions. If you are not sure of the location still PM me before and I will send my cell phone number to call if you get lost. The parking lot at this place sometimes gets crowded, but this is after Football season, so that should make the crowds a little smaller. If anyone wants to get there earlier and save us either a place in the parking lot let me know. If you haven't RSVP'ed go to this page:
http://rx7.meetup.com/55/events/3981210/
and do so. It has a place for "maybe's" if you aren't sure. This gives us a good idea of how many parking spaces to hold and how big of a table to get inside. The weather at this point looks like it might be a little chilly, but not like last time. We should be able to do the usual BS-ing outside around the cars and not freeze our a**es off like last time.
In addition, there is a Tidewater Sports Car Club autocross on the following Sunday. There are a few of our members/friends that are pre-registered. The event is at the Pungo Fairgrounds. It is a small autocross site, but the courses there are usually fun and great places to run if you have never autocrossed before. For more information go to this site:
http://tidewatersportscarclub.com/
and click on the registration link. For mapquest directions look up the address of Pungo Pizza and Ice Cream and get driving directions. The event site is almost next door to this business. Feel free to ask if oyu have any question.
When: Saturday, February 19, 2005 at 6:30 PM
Where: Hooter's
12640 Jefferson Avenue
Newport News, VA 23602
(757) 886-9464
If you aren't sure of the location go to mapquest.com and enter the address to get driving directions. If you are not sure of the location still PM me before and I will send my cell phone number to call if you get lost. The parking lot at this place sometimes gets crowded, but this is after Football season, so that should make the crowds a little smaller. If anyone wants to get there earlier and save us either a place in the parking lot let me know. If you haven't RSVP'ed go to this page:
http://rx7.meetup.com/55/events/3981210/
and do so. It has a place for "maybe's" if you aren't sure. This gives us a good idea of how many parking spaces to hold and how big of a table to get inside. The weather at this point looks like it might be a little chilly, but not like last time. We should be able to do the usual BS-ing outside around the cars and not freeze our a**es off like last time.
In addition, there is a Tidewater Sports Car Club autocross on the following Sunday. There are a few of our members/friends that are pre-registered. The event is at the Pungo Fairgrounds. It is a small autocross site, but the courses there are usually fun and great places to run if you have never autocrossed before. For more information go to this site:
http://tidewatersportscarclub.com/
and click on the registration link. For mapquest directions look up the address of Pungo Pizza and Ice Cream and get driving directions. The event site is almost next door to this business. Feel free to ask if oyu have any question.
02-20-05, 11:24 PM
#1716
Senior Member
Join Date: Mar 2004
Location: 757
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
hi, i was wondering if anyone had a socket big enough like 2" 1/2 inch socket to help me tighten that big nut that bolts the flywheel in place..
i got the nut off, now i need something to tighten it
thanks,
Greg
i got the nut off, now i need something to tighten it
thanks,
Greg
02-21-05, 12:47 AM
#1718
rotary sensei
iTrader: (5)
Join Date: Mar 2001
Location: Virginia
Posts: 2,312
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by NSXchink
hi, i was wondering if anyone had a socket big enough like 2" 1/2 inch socket to help me tighten that big nut that bolts the flywheel in place..
i got the nut off, now i need something to tighten it
thanks,
Greg
i got the nut off, now i need something to tighten it
thanks,
Greg
Chris
02-21-05, 06:01 PM
#1720
Senior Member
Join Date: Sep 2001
Location: Carrollton, VA
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by calvin
I have a socket, I think it is 2-5/16 or some such. I have the right one. Mine takes a 3/4" drive ratchet.
dale
02-21-05, 08:14 PM
#1721
Not a Racist
Join Date: Aug 2003
Location: virginia
Posts: 1,514
Likes: 0
Received 0 Likes
on
0 Posts
hey anybody have sum gsl parts their willin to give to me for cheap? i brought mine home not even an hour ago and i need a rear view mirror
not sure whqat else ill go over it tommorow after school
not sure whqat else ill go over it tommorow after school
02-21-05, 11:22 PM
#1723
Senior Member
Originally Posted by renagade_rotary
hey anybody have sum gsl parts their willin to give to me for cheap? i brought mine home not even an hour ago and i need a rear view mirror
not sure whqat else ill go over it tommorow after school
not sure whqat else ill go over it tommorow after school
-Rich
02-22-05, 08:01 AM
#1724
Rotary Freak
Thread Starter
Join Date: Sep 2001
Location: VA
Posts: 1,542
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, post your list. If Rich doesn't have it, I probably do. I don't have the lift actuators, but I know what you can do about getting new replacemets at local auto parts stores. Does your car have the rear wiper?
