Albuquerque area questions
#2
NiGHT$RIDER
iTrader: (-1)
Join Date: Aug 2008
Location: Rio rancho
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
help
lol pm me maybe able to help you out the only shop that we had closed but i know toms brother tim tom was the owner of the shop off 2nd but closed a month ago he went over sees but hes brother know eeverythin about the car if you want me to see if i can get him to help let me know
#3
Full Member
Join Date: Sep 2001
Location: Las Cruces, NM
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
I guess I will piggy back off this thread.
Can anyone recommend a good body shop. I need to have my car painted, a few pieces of body work fitted, and the seats reupholstered.
thanks
Can anyone recommend a good body shop. I need to have my car painted, a few pieces of body work fitted, and the seats reupholstered.
thanks
Trending Topics
#8
I
iTrader: (3)
Join Date: Nov 2007
Location: at home
Posts: 1,063
Likes: 0
Received 0 Likes
on
0 Posts
just pm him....here is the link to his rx7 build thread.
https://www.rx7club.com/drifting-226/my-rx7-drift-build-783006/
https://www.rx7club.com/drifting-226/my-rx7-drift-build-783006/
#10
RIP Mark
iTrader: (5)
Rotary RX isn't closed...I was just there a week or so ago talking to Tom as he was rebuilding an engine. They never answer the phone though, whenever I need to talk to them I swing by the shop. http://www.rotaryrx.com/
#16
I called RotoryRX a couple weeks ago, they told me Tom was gone, and they have no rotary mechanics. They were willing to look at my car though... but I told them I wanted to meet Tom. I just moved to Los Lunas from out of state, and was looking forward to a sharp mechanic. My '91 just failed emissions (HC 10x what they should have been at idle, and my engine is new!), and I need to figure it out. I am a little leery of letting people work on my car... I'll call racefab and see what they can do.
#18
Yeah, that is what I figured from my research on here. I have read that bad cats can cause this; my cats were new when I replaced the engine (5 yrs, 10k mi ago). I have a factory setup with the exception of street porting (Adkins engine) and Monza exhaust. My next step would be to replace the replace the plugs/wires and injectors, I think... I pulled the car from a junkyard in OH in '02. The injectors were not cleaned or replaced, I reused them with the new engine (which I am learning may not have been too bright). The original motor I pulled had blown the rear rotor, which fried the exhaust system and melted the wiring harness over the transmission hump (if this means anything). Any thoughts?
#19
The Choopster
iTrader: (4)
Join Date: May 2004
Location: Albuquerque, NM
Posts: 447
Likes: 0
Received 0 Likes
on
0 Posts
Verify that the air pump and air control valve (ACV) are working, and that the tube from the ACV to the main cat is intact. Take a look inside the cats and verify that the catalyst is still there and not blocked. I usually hold the main cat in front of a bright light and verify that I can see through the catalyst to the other end. Run the car hard immediately before your emissions test to ensure that the cats are hot and that the catalyst is performing its job optimally (although you've probably heard all this before).
Having the injectors cleaned and replacing spark plugs and wires is a good idea regardless of the emission issues. Replace your intake filter if you haven't done that either.
One interesting thing I noticed on my car is that the barometric pressure sensor thinks that it's around 4400 ft. This is about 1000 ft off, and would probably result in the ecu adding extra fuel. It's easy to correct if you've got a tunable ecu, but if you're running the stock ecu, it may be a difficult issue to lean out the fuel mixture to an acceptable ratio.
Having the injectors cleaned and replacing spark plugs and wires is a good idea regardless of the emission issues. Replace your intake filter if you haven't done that either.
One interesting thing I noticed on my car is that the barometric pressure sensor thinks that it's around 4400 ft. This is about 1000 ft off, and would probably result in the ecu adding extra fuel. It's easy to correct if you've got a tunable ecu, but if you're running the stock ecu, it may be a difficult issue to lean out the fuel mixture to an acceptable ratio.
#22
The Choopster
iTrader: (4)
Join Date: May 2004
Location: Albuquerque, NM
Posts: 447
Likes: 0
Received 0 Likes
on
0 Posts
Funny you mention this, I was going to rebuild my tranny as a project over the UNM winter break. There are way too many special tools involved though. If you find a reputable shop, could you pass the information along. Thanks.
#25
I am and I am not. I bought that one in August. So while I am the one that parks it there now, I wasn't the one who was parking it there before August. I bought it from Professor Russell in the Mech Eng dept. He kept it in pretty good mechanical shape, just having to redo the interior at this point.