General Rotary Tech Support Use this forum for tech questions not specific to a certain model year
Sponsored by:
Sponsored by: CARiD

What automatic transmission will work with a 13b?

Thread Tools
 
Search this Thread
 
Old 04-27-09 | 04:52 PM
  #1  
BUSTN's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2005
Posts: 566
Likes: 0
From: Orlando, FL
FL What automatic transmission will work with a 13b?

I am considering running an automatic in my fc. What transmission can I mount in there that will work? An adapter plate is necessary,correct? Also, only small 8" tc's the only thing worth putting in,correct? The thing is, I need a new pressure plate and clutch, as well as a slave cylinder. I rather dump that into a better set up than the t2 tranny. Although, I CANNOT afford a g-force or liberty, I am mainly looking for upgraded factory trannies, Thanks!
Old 04-29-09 | 07:13 AM
  #2  
jose roman's Avatar
Junior Member

 
Joined: Dec 2008
Posts: 40
Likes: 0
From: Puerto Rico
Originally Posted by BUSTN
I am considering running an automatic in my fc. What transmission can I mount in there that will work? An adapter plate is necessary,correct? Also, only small 8" tc's the only thing worth putting in,correct? The thing is, I need a new pressure plate and clutch, as well as a slave cylinder. I rather dump that into a better set up than the t2 tranny. Although, I CANNOT afford a g-force or liberty, I am mainly looking for upgraded factory trannies, Thanks!
Find this webside from P.R. www.nctransmission.com your goin to find what do you need....
Old 05-01-09 | 04:44 PM
  #3  
jose roman's Avatar
Junior Member

 
Joined: Dec 2008
Posts: 40
Likes: 0
From: Puerto Rico
Originally Posted by relentlessrotary
automatic trannies require engines with lots of torque to work well. rotary engines produce less torque than most engines on the road. this is why the auto with rotary has never been a good combo. Unless you can stall a rotary to 3500-4000rpm and have a gear in the rearend, it will be a slug, because you lose too much of what little power you are making, in that slushbox.
Tell me if I have a 13B turbo, 2,250 wheight ,automatic with 475 hp and run 5.63 et @121 hp 1/8 with 1.29 60 fts.......the stall speed of this torque converter its 7,300 rpm.....but on this couple past 5.63 et, the 2 step its on 5,400 rpm at the launch.......UPSSSS at 5,400 make 35 psi boost and we finish the 1/8 35psi....with a precision turbo pt76 and 96ext. small frame...

Do you think Its working automatic trannys on mazda 13B

Visit www.nctransmission.com
Old 05-01-09 | 07:57 PM
  #4  
jgrewe's Avatar
GET OFF MY LAWN
iTrader: (1)
 
Joined: Feb 2005
Posts: 2,837
Likes: 2
From: Fla.
On the strip, the powerglide is the way to go. The key is consistancy, they will do the same thing over and over again, you can't.

The whole set-up will be custom and probably bullet proof. It looks like NCT has it down right. Once its in the car you can forget about it.
Old 05-02-09 | 05:09 PM
  #5  
BUSTN's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2005
Posts: 566
Likes: 0
From: Orlando, FL
The car will be driven on the street but actually looking for performance. This car is not a daily driver due to the motor and turbo set up. I was thinking of doing a c4 or th400 with an adapter plate.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
wallyrx7
Rotary Car Performance
2
08-20-15 06:55 PM




All times are GMT -5. The time now is 05:31 PM.