This gauge pod looks awesome with rotary trim.



Rotary > Pistons

 

I'm gonna be dropping the engine in soon, all I really need to do prior is drop in my walbro255lph and rewire it.

Rotary > Pistons

 

Got the down pipe fixed where it was broken, it looks ghetto but it it's sealed inside and looks much better inside then it does on the outside.

As long as it works for a while I don't really care how it looks, hopefully I can put exhaust wrap over it so its not visible.

Here's before and after , ill take a pic of the inside later.








Rotary > Pistons

 

Cleaned up some more stuff , got it all prepped nice for the next step.









Rotary > Pistons

 

I know people are on a budget, but a welding shop could have done that for a case of beer probably. Looks like it was welded way too cold and will probably crack when a spirited run is made.
Great project, however.

 

Iif it does crack ill probably just replace the entire downpipe. I wasn't very impressed with the welding that was done but I don't know how to weld so I am pretty much stuck with it I will probably get a racing beat downpipe to replace it as soon as it cracks I hope it will last a while I won't be driving spirited until my break in is over

Rotary > Pistons

 

Ya, that weld-job is shocking. I'd just get a new one asap.

 

I'm broke right now just doing what I can to get it running, ill worry about that later.

The exhaust that's on there came with the car when I bought it, its not the greatest and I unluckily cracked that piece and had to get it welded.

So if I do get it replaced I will still have to get the next piece welded unless I replace everything up to the y pipe because they had everything welded in one piece all the way up to the y pipe, also after the down pipe it goes to 3" then goes back to 2.5" at the y (not something I would of.done personally)
>.<

So really its more complicated then just replacing the down pipe. Ugh

Rotary > Pistons

 

I cleaned up the engine bay with my air compressor using Compressed air and also blew the old.gas out the lines.

The exhaust is actually one piece all the way to the mufflers, it looks like the middle section/flex pipe is from cheap autozone exhaust parts.









Rotary > Pistons

 

Preparations for engine assembly.

Haven't actually put it together just doing a dry run to see how everything goes together so no mistakes are made











Rotary > Pistons

 

Actual assembly so far, just about ready to go in all it really needs to have put on is the clutch and oil pan.


I stuffed the holes with rags , I only took them out to take this pic.



Rotary > Pistons

 

Ready to go in



Rotary > Pistons

 

Just got the transmission prepared and put the new pivot ball on the transmission and the new release bearing.

The only major jobs left can be done after the engine is put in if need be, the only concern is a few wires in the harness that could use some attention.

1) walbro 255 install and rewire
2)fuel filter/fuel lines
3) radiator/oil cooler

I'll likely save the radiator and oil cooler for last, they just get in the way.

I have new silicone hoses to replace the questionable ones already ordered, they're on their way, so ill use the old ones for now.

Rotary > Pistons

 

Soon y'all should be seeing some pics and a video of her firing up.

Everything is ready for a go.

I still need to install my walbro fuel pump , it looks like an easy install so I may do that as I'm doing the engine after its bolted in.

Rotary > Pistons

 

the fuel pump is a breeze. Did mine a few months ago in preparation for my TII sitting in the corner of my garage

 

Looking forward to seeing it running! Looks like youre In southern va so I dont think ill get a chance to see it

 

engine is in.

working at getting everything bolted on and hooked up.







Rotary > Pistons

 

Sweet project man!

 

Thanks man, I've put alot of hard work and dedication into her.

Rotary > Pistons

 

Right now I'm in the process of fixing some stuff on the wiring harness



Rotary > Pistons

 

I hate wiring.. But it's ganna be bad *** when it's finished!!

 

should be ready to fire up tommorow, sadly I broke my earls bolt for the banjo bolt mod but I was able to easily get it out and use a stock pd until I can get another.

here's how how far I've gotten.





Rotary > Pistons

 

Not much is left , I got pretty much everything on, it got dark so ill finish tommorow.





Rotary > Pistons

 

You should look into getting a dual altenator pulley.

 

Already have one I just don't have the impact gun to switch it

Rotary > Pistons