I'm 99% certain I've seen a thread with pictures...but more important part numbers to order from Summit or wherever to redo fuel lines with fitting, ss lines and an aeromotive FPR.

My search-fu is failing. Anyone know of a thread like this? Need to do some ordering!

 

Well it's not like there is only 1 way to do your fuel setup...there are lots of options. There are ready to go kits, there are semi-complete kits, there are custom options. Lots of configurations you could go with, it all depends on your setup, goals, and personal taste.

Here's the setup I'm using (parallel operation: stock primary rail w/ 550cc injectors & KG Parts secondary rail w/ 1600cc injectors, then all custom lines):

https://www.rx7club.com/classifieds-violations-265/theories-why-im-always-poor-1993-ssm-build-951172/page6/



Here's my final parts list, IIRC:

(x3) -6AN Straight Push-on Hose End
(x6) 90degree -6AN Push-on Hose End
(x1) 180degree -6AN Push-on Hose End
(x1) Straight 3/8" NPT to -6AN Adapter Fitting (for KG Parts secondary rail)
(x1) 90degree 3/8" NPT to -6AN Adapter Fitting (for KG Parts secondary rail)
(x2) 90degree 1/4" NPT to -6AN Adapter Fitting (for factory primary rail)
(x1) -6AN "Y" Splitter
(x3) Straight -6AN to -6AN O-Ring Adapter Fitting (for Aeromotive FPR)
A few feet of -6AN size push-on fuel line

You can also check out Damian's thread for more info on configurations:
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/fuel-system-upgrade-how-write-up-kgparts-kit-404091/

Then again there are a number of ready-to-go kits. For example:
http://www.rx7store.net/category_s/93.htm

 

Gringo my set up is as follows. I set them by category and what is needed per item to run full fittings system.

RAILS-
Rx7store secondary rail
Kg parts primary rail
3-3/8 to -6AN adapter fittings
1- 90degree to -6AN adapter (for secondary rail front clearance)
2- 90 degree to-6AN hose end
1- 45 degree to -6AN hose end
1- -6AN to straight hose end

FPR-
Aeromotive 13109
3- 3/8 to -6AN adapter fittings
1- -6AN to straight hose end
1- -6AN to 120 degree hose end
1- -6AN to 45 degree hose end

YBLOCK-
Jegs y block
2- 3/8 to -6AN hose end
1- 3/8 to -8AN hose end


FUEL PUMP-
Bosch 044
1- 12mm to -8AN adapter
1- -8AN to -8AN female to female coupler

Fuel Pick up unit-
1- -8AN to 3/8 bulkhead adpater
1- -6AN to 3/8 bulkhead adapter

FUEL FILTER
Summit 60micron -8AN to -8AN filter inline

FUEL HOSES
1- -8AN feed tofrom tank to Y block- aprx 7ft
2- 90 degree 8-AN hose end
1- -6AN from y block to rails,fpr,and back to return to tank -10 ft
2- 90 degree -6AN hose ends

 

This is great reference info!

 

Alex.....what are your fuel pick-ups? I'm looking for a couple as well. this pushes your fuel pickup considerably lower correct? are you running the hyperion in tank baffle?

 

Thank you gentlemen. Theorie's thread was the one I was originally looking for but Alex came through like a champ! Thank you for the contribution!

 

I know what picture you're looking for. I was looking at it just a few days ago. I'm going through my browser to try and find it. Crossing my fingers.

EDIT - I found what I've been looking at for the past few days, I couldn't find it because it wasn't a thread.

http://www.reganrotaryracing.com/fdfuelsystem.htm