Speed limiter cut
08-16-08 | 01:36 AM
#34
For the OP, it's hard to say which wire to cut on the 16bit ECU, there aren't many people with 96+ cars on this forum. Your best bet would be to ask a JDM RX-7 shop (RE-A, FEED, Scoot, etc), OR get a Knightsports FCD. They are cheap and they remove fuel cut as well as the speed limiter.
08-16-08 | 02:31 AM
#35
yes, all JDM cars are speed limited at 111mph.
For the OP, it's hard to say which wire to cut on the 16bit ECU, there aren't many people with 96+ cars on this forum. Your best bet would be to ask a JDM RX-7 shop (RE-A, FEED, Scoot, etc), OR get a Knightsports FCD. They are cheap and they remove fuel cut as well as the speed limiter.
For the OP, it's hard to say which wire to cut on the 16bit ECU, there aren't many people with 96+ cars on this forum. Your best bet would be to ask a JDM RX-7 shop (RE-A, FEED, Scoot, etc), OR get a Knightsports FCD. They are cheap and they remove fuel cut as well as the speed limiter.
08-20-08 | 12:08 AM
#42
I did 210 km/h, at 190 km/h I feel a STRONG lack of power, this is strange!
08-21-08 | 08:25 AM
#45
Sheriff´s FD
Joined: Sep 2007
Posts: 123
Likes: 0
From: austria
If there are more cables with the same colour, could you tell us if its the, for example, 3rd cable from left or so?
thx
Andi
08-21-08 | 09:49 AM
#46
This is the right wire! Warning, there's two or three wires red and green, this is the right one. You absolutely need to unplug the yellow plug (the lowest or the highest, I don't remember which one of those two). Then, you'll see the famous wire.
To unplug the yellow wire, you need to push the button in the back of it, and to PULL HARD (Do not be scared to pull by the wires, this is okay!).
06-18-09 | 03:17 AM
#48
Sheriff´s FD
Joined: Sep 2007
Posts: 123
Likes: 0
From: austria
Hehe i didnt cut the wire so far, as you wrote, after reading the whole thread, i have a bad feeling about cutting wires too.
So i guess i will start at first with a redom ecu ( since they are cheap ) or better, with a pfc - but at first, my car has to run without problems.
thx
Andi
So i guess i will start at first with a redom ecu ( since they are cheap ) or better, with a pfc - but at first, my car has to run without problems.
thx
Andi
06-22-09 | 09:57 PM
#49
306 motorclub member
Joined: May 2009
Posts: 42
Likes: 0
From: Saskatchewan, Canada
its the bottom plug of the ecu. i did this mod today and it worked fine!
im free of the limiter!
i also put a bullet connector on the wires for easy reconnection if need be at a later date!
im free of the limiter!
i also put a bullet connector on the wires for easy reconnection if need be at a later date!
12-03-11 | 04:30 AM
#50
Junior Member
Joined: Nov 2011
Posts: 5
Likes: 0
From: Germany
it works on the 16bit ECU, too. i just tried it an my 97 model
2 days ago. but, the speed signal for my HKS Turbo Timer was
connected to this green/red cable and now it wont read any speed.
can i just ground this wire or is there another speed signal
i can tap my HKS into? i need the digital speedo from the
HKS to read speeds above 180km/h...
2 days ago. but, the speed signal for my HKS Turbo Timer was
connected to this green/red cable and now it wont read any speed.
can i just ground this wire or is there another speed signal
i can tap my HKS into? i need the digital speedo from the
HKS to read speeds above 180km/h...