just powdercoating some things
#27
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Ok I'm powder coating Stupid
How do you basically do it?
Is it just spray on and bake?
I thought you had to some how connect the parts to electricity for the powder to stick to it?
What about bare metal parts? I can't imagine you being able to spray the coating on something that has that thin protective layer of oil to prevent it from rusting, so did you have to sandblast anything and then immediately coat it?
#28
Senior Member
HOLY FRIGGIN MIRROR! Very nice with the powder!! Chrome powder is tough to produce, that is the best i've ever seen!
i wanna see it installed!!
nice job,
big will
i wanna see it installed!!
nice job,
big will
#29
built my own engine
Thread Starter
powder goes on electrostatically, it's a low pressure (15psi-10psi) system, it's like shaking baby powder on a part and then you bake
prep/application is the key to a good finish, my secrets are acetone, more acetone, and some more acetone
it's not my motor, it's r71's motor, rob golden at pineapple still has my motor, ARG
prep/application is the key to a good finish, my secrets are acetone, more acetone, and some more acetone
it's not my motor, it's r71's motor, rob golden at pineapple still has my motor, ARG
#30
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by 93BlackFD
powder goes on electrostatically, it's a low pressure (15psi-10psi) system, it's like shaking baby powder on a part and then you bake.....
powder goes on electrostatically, it's a low pressure (15psi-10psi) system, it's like shaking baby powder on a part and then you bake.....
At how many degrees and for how long?
Oh, is it possible to powercoat an allready powdercoated item, or must it be stripped to bare metal?
#31
built my own engine
Thread Starter
400F, you can use your kitchen oven if you want
it'd be best to strip the item, stripping powder is not easy at all
let a professional strip it, and you can powder it yourself if you buy the gun
www.eastwoodco.com
it'd be best to strip the item, stripping powder is not easy at all
let a professional strip it, and you can powder it yourself if you buy the gun
www.eastwoodco.com
#32
On the front plate, the chroming makes it look like that or did you use like a pearl in it ? That looks sweet, if I knew you could powder chrome I wouldnt have spent so many hours polishing all my stuff...!
#33
built my own engine
Thread Starter
that's just straight up powder man, no special tricks other than good surface prep
here's the tranny bellhousing which i spent less time prepping, and thus, some embedded chemicals in the metals released gasses making little pits
http://68.209.118.245/pics/DSCN1184.JPG
http://68.209.118.245/pics/DSCN1183.JPG
http://68.209.118.245/pics/DSCN1182.JPG
and on the last pic, i went and cleaned off the excess powder that ended up on the mating surfaces (tranny/engine)
looks a lot better, i'll take pics of the whole tranny reassembled when i'm done
here's the tranny bellhousing which i spent less time prepping, and thus, some embedded chemicals in the metals released gasses making little pits
http://68.209.118.245/pics/DSCN1184.JPG
http://68.209.118.245/pics/DSCN1183.JPG
http://68.209.118.245/pics/DSCN1182.JPG
and on the last pic, i went and cleaned off the excess powder that ended up on the mating surfaces (tranny/engine)
looks a lot better, i'll take pics of the whole tranny reassembled when i'm done
Last edited by 93BlackFD; 12-13-03 at 04:22 PM.
#34
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by 93BlackFD
that's just straight up powder man, no special tricks other than good surface prep....
that's just straight up powder man, no special tricks other than good surface prep....
http://www.eastwoodco.com/itemdy01.a...0169&Dep_Key1=
I also saw the reflective chrome and both are different part numbers.
Have you seen both?
#36
Eats, Sleeps, Dreams Rotary
iTrader: (4)
Join Date: Apr 2003
Location: Denver, NC
Posts: 3,531
Likes: 0
Received 0 Likes
on
0 Posts
Did you do the inside of the bell housing in a different color than the outside? If so did you have to do it twice?( bakeing process, or did you spray both then bake?) Looks nice, and I bet it is easier to clean. And it's protected from the elements now.( Our Aluminum out here gets ugly fast! I may do this now. Thanks for shareing. Dave
#37
built my own engine
Thread Starter
i did the outside chrome and then clear, i was worried because the clear yellows above 350F when you're curing it, but you "run it out (melt it)" at the standard 450F
i did the wrinkle black on the inside last, and surprisingly it worked, i think the trick was that i turned the inside facing down, so the heat got trapped in the bellhousing and baked it faster
eitherway, if i did it again, i'd do the black on the inside first, and the chrome last
i had a tranny leak before and it pissed me off when i wiped off the fluid, because it had stained the bellhousing, so i couldn't tell where the leak was coming from
also i figure it will make it easier to clean out since i've pulled my motor so frequently, makes handling it a lot better
i did the wrinkle black on the inside last, and surprisingly it worked, i think the trick was that i turned the inside facing down, so the heat got trapped in the bellhousing and baked it faster
eitherway, if i did it again, i'd do the black on the inside first, and the chrome last
i had a tranny leak before and it pissed me off when i wiped off the fluid, because it had stained the bellhousing, so i couldn't tell where the leak was coming from
also i figure it will make it easier to clean out since i've pulled my motor so frequently, makes handling it a lot better
#39
built my own engine
Thread Starter
thanks man, i'll post pics of the throttle body and greddy elbow later today, and we're also doing his entire suspension, subframe (front/rear) and the list goes on
#41
built my own engine
Thread Starter
yeah, i can powder for anyone, just hit me up on PM or email b_thompson@bellsouth.net
i don't try to get rich off of it either
i don't try to get rich off of it either
#43
built my own engine
Thread Starter
#48
built my own engine
Thread Starter
i use a kitchen oven and a hotcoat gun from eastwood, a 50lb abrasive blaster and acetone for cleaning
the secret to good setup is to prep well, blast throughly, and to mask well
having the plugs/tape/masking accessories helps to keep the part functional, determining the bake times, etc for a part is crucial as well. it helps to have someone with experience guide you and help prevent mess ups. baking is a good method but infrared lamps work well too, just take longer
the secret to good setup is to prep well, blast throughly, and to mask well
having the plugs/tape/masking accessories helps to keep the part functional, determining the bake times, etc for a part is crucial as well. it helps to have someone with experience guide you and help prevent mess ups. baking is a good method but infrared lamps work well too, just take longer
#49
Banned. I got OWNED!!!
Join Date: Dec 2003
Location: where
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Ihad my upper plenum powder coated wrinkle black with jet hot in the center and underneath.
looks sick.
I am going to ceramic coat the outside engine block with near chrome.
i just want that bling bling look, even on the iron block.
looks sick.
I am going to ceramic coat the outside engine block with near chrome.
i just want that bling bling look, even on the iron block.
#50
Banned. I got OWNED!!!
Join Date: Dec 2003
Location: where
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Jet hot ceramic coating near chrome has more of a metallic look than powder coat.
BTW, I think that near the exhaust ports and turbos is where the heat might start to degrade the powder coat over time.
BTW, I think that near the exhaust ports and turbos is where the heat might start to degrade the powder coat over time.