EVO-R GTC FD race car
06-05-03, 07:45 AM
#26
Rotary Freak
Join Date: Aug 2001
Location: Boston, MA
Posts: 1,635
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by particleeffect
anyway, the only article in scc i remember about flat black was project silvia. as for which, scc was damn sure not the first, but we all know that. chill.
anyway, the only article in scc i remember about flat black was project silvia. as for which, scc was damn sure not the first, but we all know that. chill.
06-05-03, 03:34 PM
#27
Full Member
Thread Starter
Join Date: Jun 2002
Location: New York
Posts: 64
Likes: 0
Received 0 Likes
on
0 Posts
Thanks guys. I'll try to contact PFS about 20B installation. Today we just strip a 99 FD right hand drive. Converting it to left hand drive by cuttting the firewall from a salvage car. I have many sets of Trial N1 carbon fiber racing seats. Anyone interest? I'm putting one on my car after it is done re painting. This one will look the same as flat black one but the paint is not flat.
06-05-03, 04:04 PM
#28
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by Jay Shieh
..... Top speed was at 293KM. This car will be for track race only. ....
..... Top speed was at 293KM. This car will be for track race only. ....
182mph is pretty decent
Mayybe you should think about upgrading to the Vielside 320km Speedo
06-05-03, 07:06 PM
#31
in slow, out fast!
Join Date: Apr 2002
Location: Florida
Posts: 1,388
Likes: 0
Received 0 Likes
on
0 Posts
06-05-03, 07:38 PM
#32
Full Member
Thread Starter
Join Date: Jun 2002
Location: New York
Posts: 64
Likes: 0
Received 0 Likes
on
0 Posts
These wheel was off from a JDM damaged car in japan. It says mazdaspeed on the wheel and each little nuts on the sides says rays. Center cap has madaspeed and on the wheel stamped with rays mazdaspeed. I was told this rims was original shown with the 15th anniversary mazdaspeed RX-7. Anyone has a picture of that?
06-07-03, 12:36 PM
#36
Originally posted by Jay Shieh
The engine is running with Stock turbo. Since our race track is small with sharp turns, no point for using big single turbo. But I have Greddy 3 layer intercooler, and custom radiator. On Board I have Defi guages, Recaro seats, 5 point seat belt, HKS F CON V PRO, and Blitz boost controller. Basicly it is almost stock on power. The exhaust is full straight pipe. The rims are RAY's enginnering made for Mazdaspeed. I pick those up from a JDM car. It was a steal for only US$800 with tires. I tis using mazdaspeed double plate clutch. Top speed was at 293KM. This car will be for track race only.
I'm working on another one for 1/4 race. But I don't think I can make it as quick as ones in the states. Maybe with some of club member's help. I can put in my 20B motor sitting in the back of my shop. Anyone know what I need to have 20B install on my other FD? Thanks for the help!
The engine is running with Stock turbo. Since our race track is small with sharp turns, no point for using big single turbo. But I have Greddy 3 layer intercooler, and custom radiator. On Board I have Defi guages, Recaro seats, 5 point seat belt, HKS F CON V PRO, and Blitz boost controller. Basicly it is almost stock on power. The exhaust is full straight pipe. The rims are RAY's enginnering made for Mazdaspeed. I pick those up from a JDM car. It was a steal for only US$800 with tires. I tis using mazdaspeed double plate clutch. Top speed was at 293KM. This car will be for track race only.
I'm working on another one for 1/4 race. But I don't think I can make it as quick as ones in the states. Maybe with some of club member's help. I can put in my 20B motor sitting in the back of my shop. Anyone know what I need to have 20B install on my other FD? Thanks for the help!
. ps: hope you have a rollcage
06-07-03, 01:02 PM
#37
Full Member
Thread Starter
Join Date: Jun 2002
Location: New York
Posts: 64
Likes: 0
Received 0 Likes
on
0 Posts
We're working on the roll cage next month. Currently have front mount intercooler only. The HKS V pro had hardness for U.S version. You have to buy it for older version FD.
06-07-03, 06:34 PM
#38
Junior Member
Join Date: Jan 2003
Location: NorCal
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
It looks like you're in Taiwan. Are you in Taipei also? My cousin John **** owns a shop called JW Racing there also does a lot of work on FD's and he's done a couple RH to LH conversions. Just wondering if you know him since he's a pretty big FC/FD nut.
06-08-03, 03:20 PM
#40
Junior Member
Join Date: Jan 2003
Location: NorCal
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
The next time in Taiwan, we'll have to meet up. It's not often that you see FD's or meet FD owners in Taiwan. I see them on the street once in a very long while, with the exception of the JW cars.
Btw, what's an SA?
Btw, what's an SA?
06-08-03, 03:27 PM
#41
in slow, out fast!
Join Date: Apr 2002
Location: Florida
Posts: 1,388
Likes: 0
Received 0 Likes
on
0 Posts
lol i just saw pics of this guys car on ebay... some guy is selling the rear bumper...used ervy one of this guys pics..
heres the link
http://cgi.ebay.com/ebaymotors/ws/eB...tem=2418545514
heres the link
http://cgi.ebay.com/ebaymotors/ws/eB...tem=2418545514
Thread
Thread Starter
Forum
Replies
Last Post
