Engine Help
#1
Cause I Can
Thread Starter
iTrader: (3)
Join Date: Mar 2010
Location: Cal State Fullerton
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
Engine Help
So I started my car up today as normal, It started up and I was letting it warm up and I noticed the cars temps werent going up, then out of the blue the engine shut off, and I could get it to start back up, is my engine done, compression numbers were check last week 65 in the back and 100 in the front
Trending Topics
#8
Original Gangster/Rotary!
iTrader: (213)
I hope your budget is fairly high..... with that kind of mileage, the best thing you can do is buy a brand new engine. Ray at Malloy has them in stock, I was just there and saw one waiting to be shipped out. Call him at 888 533 3400, they're around $4200 IIRC.
#9
Cause I Can
Thread Starter
iTrader: (3)
Join Date: Mar 2010
Location: Cal State Fullerton
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
I can't be positive, that it is in fact it is the factory engine, with that said , I'm actually only 19 years of age and go to Cal State Fullerton , rebuilding this engine would be very easy to me ,because my dad was a rotary man before he passed away as a LA County sheriff so he did teach me well I just don't have a cherry picker nor the time since I go to school all day and work in the jails at night, but another engine sounds like an option
#15
Rotary Enthusiast
iTrader: (34)
Join Date: Apr 2009
Location: japan
Posts: 771
Likes: 0
Received 0 Likes
on
0 Posts
Like others have said it will cost you more to piece one together than to buy a reman with that level of mileage on it.
Most likely the only thing reusable in your engine right now is your eshaft, one (maybe two) rotors, and your irons. Even the irons probably have a lot of wear and could be damaged from the apex seal.
Usually when an apex seal goes it takes out the rotor housing, and could possibly damage the rotor, 2 irons, and your turbo(s).
That's why it's always good to rebuild an engine when the compression gets in the 80's. At that point you still have usable parts.
Most likely the only thing reusable in your engine right now is your eshaft, one (maybe two) rotors, and your irons. Even the irons probably have a lot of wear and could be damaged from the apex seal.
Usually when an apex seal goes it takes out the rotor housing, and could possibly damage the rotor, 2 irons, and your turbo(s).
That's why it's always good to rebuild an engine when the compression gets in the 80's. At that point you still have usable parts.
#16
Cause I Can
Thread Starter
iTrader: (3)
Join Date: Mar 2010
Location: Cal State Fullerton
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
I haven't drove it since the apex seal went bad, my engine was running 99-98 compression day before sevenstock then a week after it didn't want to start so I didn't even mess with it that's when I towed it to get the compression check I'm confident that the engine isn't original seeing that it's all black and silver
#17
There is no such thing as "just a broken apex seal". When seals break they typically cause damage to the rotor and corresponding damage to the housing. Additionally the seal debris exiting the engine causes damage to the turbine wheel(s) on the turbo(s).
Here is an engine that we tore down that just had chipped seals, it still ran, just poorly. This is considered minor damage in comparison to engines that throw all the seals.
Even with this much damage and replacement parts needed our standard $1500 rebuild + a rotor and housing would not come anywhere near the $4200 for a Mazda reman.
Here is an engine that we tore down that just had chipped seals, it still ran, just poorly. This is considered minor damage in comparison to engines that throw all the seals.
Even with this much damage and replacement parts needed our standard $1500 rebuild + a rotor and housing would not come anywhere near the $4200 for a Mazda reman.
Last edited by Banzai-Racing; 10-06-10 at 05:24 AM.
#18
dorito powered
iTrader: (5)
Join Date: Mar 2008
Location: Lincoln, NE
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
it always sucks to see the carnage, best of luck OP, if you can get the motor out and torn down you'll know better what you're dealing with, I'm tearing mine down in a week and a half
#19
Cause I Can
Thread Starter
iTrader: (3)
Join Date: Mar 2010
Location: Cal State Fullerton
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
Thanks banzai, that actually makes sense because my turbos were making a strange noise, I bought some rebuilt turbos so I'm good there, also when an apex seal goes it breaks then shoots out the exhaust ?
#21
LSx 7.0L
iTrader: (20)
Good luck man. There's already been some great advice given. Most people in this thread probably speak from direct experience of breaking an apex seal (or seals), but I've been there as well. When mine broke, I split 2 seals out of the rear housing. It took out the housing, rotor, and my secondary turbo (was still runnin twins at the time, thank God).
You're just going to have to tear it down to see the carnage, or go with a new motor...Either way, best of luck!
You're just going to have to tear it down to see the carnage, or go with a new motor...Either way, best of luck!
#22
Cause I Can
Thread Starter
iTrader: (3)
Join Date: Mar 2010
Location: Cal State Fullerton
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
Do you guys think that throwing bnrs on a HBP motor would be bad?
I only say this because I know someone selling a rebuilt one for cheap,
That I could pick up within the next couple days
I only say this because I know someone selling a rebuilt one for cheap,
That I could pick up within the next couple days
#25
Original Gangster/Rotary!
iTrader: (213)
I made 420 rwhp on BNRs with a streetported engine back in like 2006...... this was on 17 psi with 5 gallons of c16 in the tank as insurance. I made almost 400 on 15 psi and pump gas IIRC. Search under my username, the thread is out there.