ASP Intercoolers announcement
04-30-06, 12:26 PM
#26
Originally Posted by TRISPEEDFD3S
I can't wait for the site. I think I've decided to go SMIC route with a meidum and that Air Pump friendly pipe.
sorry for the delays guys, We plan to have everything going on the ICs right after the on-lap-of-america event, so mid-May.
05-16-06, 09:49 PM
#30
None
Thread Starter
2.75" inlet and outlet. I have the air pump pipes now so if anyone needs one let me know. Damian should have a number out of this batch as well once they get settled in. I'm actually waiting on some ducts right now though for a couple people. It's always something.
06-30-06, 10:29 AM
#31
Just as a FYI, we have the site up and capable of accepting orders for the cast air-pump friendly Turbo->IC pipe.
We have a limited number for sale out of the last run Kevin did, then there will be a delay to get the next shipment, so if you need one soon order it quick.
We have a limited number for sale out of the last run Kevin did, then there will be a delay to get the next shipment, so if you need one soon order it quick.
07-30-06, 11:04 PM
#42
On Damian's street car, which has the medium, there's about 5" imbetween the intercooler and the light housing/car frame on the passenger side. There is some free play, and the duct would support moving it over an inch or two, but it depends on what you are planning on doing with the battery as well.
Looking at the intake, I would say that you could make it fit, but it may be a little more work that just a drop in.
-Andrew D.
Looking at the intake, I would say that you could make it fit, but it may be a little more work that just a drop in.
-Andrew D.
07-31-06, 07:48 AM
#43
Original Gangster/Rotary!
iTrader: (213)
Do you offer the non-airpump turbo-->ic pipes seperately? mine is all beat up from smacking on my old R1 strut bar that sat too low. I have since switched to a higher strut tower bar, and don't like the looks of the pipe.
08-01-06, 12:11 AM
#44
Originally Posted by GoodfellaFD3S
Do you offer the non-airpump turbo-->ic pipes seperately? mine is all beat up from smacking on my old R1 strut bar that sat too low. I have since switched to a higher strut tower bar, and don't like the looks of the pipe.
You can check it out on the site...
www.2dperformance.com
There's a link to the (raw) cast air pump pipe.
Let me know if you have any questions.
08-01-06, 07:37 AM
#46
Original Gangster/Rotary!
iTrader: (213)
Originally Posted by GooRoo
We do, but it's the newer cast pipe that kevin made to clear the air pump.
You can check it out on the site...
www.2dperformance.com
There's a link to the (raw) cast air pump pipe.
Let me know if you have any questions.
You can check it out on the site...
www.2dperformance.com
There's a link to the (raw) cast air pump pipe.
Let me know if you have any questions.
08-01-06, 11:06 AM
#47
None
Thread Starter
They can still do the old style tubes, I don't know if they have any of those particular bends right now though. I turned over my remaining tubing to them and I don't think there were any that are needed for that.
08-01-06, 11:33 AM
#48
Originally Posted by Kevin T. Wyum
They can still do the old style tubes, I don't know if they have any of those particular bends right now though. I turned over my remaining tubing to them and I don't think there were any that are needed for that.
If you wanted that particular pipe, we could order it.
08-01-06, 11:47 AM
#49
development
Originally Posted by damian
will medium work with stock elbow?
08-01-06, 11:57 AM
#50
Originally Posted by dubulup
medium/larger = same price?
will medium work with stock elbow?
will medium work with stock elbow?
Niether kit works well with the stock elbow, the kit is setup to use the Greddy elbow. Of course if you wanted to do some fabrication you could make it work, but it might end up being more expensive in terms of time and materials.
Thread
Thread Starter
Forum
Replies
Last Post
ls1swap
3rd Generation Specific (1993-2002)
17
06-03-24 03:25 PM
Captain Hook
2nd Generation Specific (1986-1992)
13
10-04-15 06:35 PM
