talljosh85

iTrader: (3)

Does anyone have the link for the guy who did the full oil filter comparison? It wasn't for RX-7s, but he tested several different brands, took them apart and compared them, he noticed a big difference between some of the brands. I can't remember the link or which filters did the best, but he proved his point that all oil filters are not created equal. I'll look for it and post the link if I can find it on a different computer. Oh yeah, I run a Mobil 1 and it seems to work quite fine.

croatian 3gen

hey guys, when buyin an oil filter from Mazda don't tell them it's for a rx-7, tell them it's for a mazda v6 engine...it's the same filter but alot cheaper. just thought you wanna know

mfigr1

I use the mostly mazda filters or bosch. In the mazda I will use either the short one (FD3S) or the earlier one which is taller and has more capacity. Never had a problem with leakage.

ReodDai

when I get to work I'll look up the product numbr of the filter we use

apexkw

where do you guys get the mobil 1 oil filter...i have been wanting to try it but the local stores dont carry it

DCrosby

Running over stuff on the FD shouldn't cause an oil filter leak, maybe an oil pan leak, but definitely not a filter leak...

**** I just go to Jiffy Lube Every 2Kmi, and get new oil and filter every time.. and if it leaks it's their butt.... and the oil never gets enough time to get really dirty... due to new filter / oil, then @ 20K intervals I'll do a oil change back to back @ 200 Mi to get what stays in the oil coolers clean....

RX7-2NR

My k/n hasn't leaked, try another one. Your filter gasket might be missing or damaged. the part # is (HP-1008). K&N claims on the box that they are leak proof, I use them on all my vehicals. The auto parts store near you might not stock them but they can get them in less than a week, save the wait next time-buy a few.

mfigr1

You can get them at the local AutoZone if you have them in your area.

boostedrotor

i have been using WIX filters with no problems.....i have seen a cutaway of the fram hp-1 vs. the WIX and the WIX has a lot more filter material inside, i run 20-50 synthetic......

SNracing

i used an aftermarket 1, purolater i think, seemed to work ok, but ive read several threads about aftermarket 1's saying otherwise. so now i just use the oem. also the oem comes with a new washer to put on the oil plug. never had a problem with the oem.

damian

iTrader: (2)

i goto checker auto and get the generic whatever oil filter and they dont leak, i have never had an oil filter porblem on either of the 3rd gens i have owned, i just replace them often, every oil change (3000K miles or so)

Senna

Ok, how many of you guys have washers on your oil plugs?? And Kris, what filter are you using now? How's it going man, hope you're over your cold. Hey I'm assuming the "house with the rx-7 that never runs" isn't me right??!! LOL..

SleepR1

Purolator, Bosch, Mobil 1 (expensive), and stock OEM are oil filters I've used with good results.

David Beale

Just bought my first non-Mazda filters at Canadian Tire. They don't appear to leak.
Just for your info.:
1st gen filters are quite large - good capacity and filtering ability.
2nd gen filters were reduced in diameter by half.
3rd gen filters are tiny and I doubt they filter much before plugging (and going to bypass).

All above fit in the 3rd gen. I used the first gen filter as the car had one on when I bought it so I knew it would fit. They contain much more filtering medium. They should actually filter much longer before going into bypass. If you wonder what I'm talking about, the filter evaluation discuss' it. Basically, what he found was the filters don't do much after about 500-1000 mi. It's at http://www.angelfire.com/indie/truck/oilfilterstudy.htm

gdnimr0d

iTrader: (4)

i dont know about you guys but my K and N works like a charm no oil leaks here and her idle sounds much better

fastcarfreak

i dont know if there is a real difference, but the part number for the K&N oil filter is HP-1004. maybe both fit?. I just purchased one today.
adam

Senna

"i dont know if there is a real difference, but the part number for the K&N oil filter is HP-1004. maybe both fit?. I just purchased one today."

adam

I just ordered two today and I believe the part # is HP-1008.

kensan

A little off topic but:

Do you guys tighten the filter by hand or by mechanical means? What confuses me is that I find two different methods prescribed by the 1993 shop manual here:

http://www.scuderiaciriani.com/rx7/s...e_services.pdf page A-7 which says to "...tighten the oil filter fully by hand"

and here:

http://www.scuderiaciriani.com/rx7/s...ion_system.pdf page D-7 which prescribes the mechanical method.

Hyperite

Don't do that, the pressure in the oil system changes with a differently sized filter. Not good.

Zoomspeed

Alot of the instructions with the oilfilters say to jsut tighten it by hand. So thats what I do. It really dosnt' need to be that tight.

theorie

iTrader: (31)

i have been using the Mobil1 filter at like $12 a pop.

havent had any engine problems (or oil leaking problems) with my car for the past 15k miles.

dubcaps

i use the purolator pure one filters from the FC. hasnt ever leaked and does the job well.

rotorbrain

ive been using pureone filters on all my cars for over a year now. . . its a great filter. thats what i use. . . this thread looks like it should be using a poll at the top.

paul