About to throw the fd away
#26
All out Track Freak!
iTrader: (263)
Join Date: Jul 2001
Location: Charlottesville VA 22901
Posts: 10,672
Received 412 Likes
on
250 Posts
so, was the relay shot then?
Fritz....so, if the wiring were bad...that doesn't make sense. Wouldn't that mean it would be idling like total crap as you said? Mine seems to idle smooth...and yes...I didn't get a CEL after a 1/2 hour of driving. So, if the wiring weren't good, then wouldn't it be running like trash because it wouldn't be giving feedback to the ECU? Are relays easy enough to tell when they are shot?
Fritz....so, if the wiring were bad...that doesn't make sense. Wouldn't that mean it would be idling like total crap as you said? Mine seems to idle smooth...and yes...I didn't get a CEL after a 1/2 hour of driving. So, if the wiring weren't good, then wouldn't it be running like trash because it wouldn't be giving feedback to the ECU? Are relays easy enough to tell when they are shot?
So your car is idling fine?
It only bogs under acceleration?
Have you boosted it or floored to see how it runs under boost?
You disconnected the o2 sensor and the car idles fine?
you drive it with the o2 sensor diconnected and the car doesn't behave any differently?
If all this is true then you have some sort of engine harness or ECU problem.
I'm pretty sure a stock FD with stock ECU will idle very ruff even like it's on one rotor and smoke without the o2 sensor connected.
Give us all more details about how the car runs idles etc.....
#27
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
So your car is idling fine? When I get it to idle, it is smooth 90%. Sometimes it will surge up and down. if I have it idling at 1000, and tap the gas upto 2 or 3k, on it's way down, it will stumble and start to usually idle around 1200.
It only bogs under acceleration? Correct
Have you boosted it or floored to see how it runs under boost? no, staying out of boost with only 600 miles on the motor
You disconnected the o2 sensor and the car idles fine? Yes
you drive it with the o2 sensor diconnected and the car doesn't behave any differently? Seemed the same
If all this is true then you have some sort of engine harness or ECU problem.
I'm pretty sure a stock FD with stock ECU will idle very ruff even like it's on one rotor and smoke without the o2 sensor connected.
Give us all more details about how the car runs idles etc.....
trev
#29
Rotary Freak
Join Date: Nov 2001
Location: trinidad and tobago
Posts: 2,715
Likes: 0
Received 0 Likes
on
0 Posts
Nope , the leading plugs BOTH fire at the same time in wasted spark mode , its the trailing plugs that you need to be careful with . Just for the record , I ran my car without an O2 sensor for more than a year with no problems what so ever ! You can also look at your Knock sensor , if its disconnected or bad the ECU will retard the timing .
#30
All out Track Freak!
iTrader: (263)
Join Date: Jul 2001
Location: Charlottesville VA 22901
Posts: 10,672
Received 412 Likes
on
250 Posts
Nope , the leading plugs BOTH fire at the same time in wasted spark mode , its the trailing plugs that you need to be careful with . Just for the record , I ran my car without an O2 sensor for more than a year with no problems what so ever ! You can also look at your Knock sensor , if its disconnected or bad the ECU will retard the timing .
when running the PFC you can get away without using the sensor but I'm pretty sure I remember some serious havoc when running a stock ecu and forgetting to plug the o2 sensor back up.
That's actually pretty convenient thing to know
#32
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Nope , the leading plugs BOTH fire at the same time in wasted spark mode , its the trailing plugs that you need to be careful with . Just for the record , I ran my car without an O2 sensor for more than a year with no problems what so ever ! You can also look at your Knock sensor , if its disconnected or bad the ECU will retard the timing .
Trev
#33
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
welp, changed the Lead wires around, and as mentioned, didn't change anything. my connector broke for the airpump (which again is on the car, but all capped off) so I would have to plug it in by inserting the 2 prongs into the airpump-side of the connector...would plugging that in have any effect? I know the airpump doesn't give any feedback to the ecu, but just a thought....i think swapping ecu's is next or testing the fuel pump relay.
#35
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Alright, so I swapped out my 93 cali ECU for a 93 non-cali remanufactured ecu. I erased codes and checked for them with this ecu. I am still getting 30, 33, 38, 39. However, I am NOW getting 51 (fuel pump relay) I did some testing of the relay itself by removing it and connecting a direct 12v souce to terminals A and B on the relay. It made the clicking noise I anticipated it would. With voltage connected, I checked the resistance in ohms between C and D and sure enough it was zero as I expected. Relay checks out. I put it back in. For kicks and giggle, I jump F/P and GND to make sure the fuel pump is operating. That was good. I removed the rubber fuel feed line and tested it...it didn't **** the fuel out with pressure, but it flowed well enough to fill a coffee mug in a matter of 3-5 seconds. Fuel filter is new. So, I went to start it. It cranked and started for about 2 seconds and died. I tried again, but just cranks. I thought it could be flooded. Waited till morning and tried starting...still just cranking. I will swap out ECUs again and try. I guess I am wondering why my stock cali ECU didn't pick up on the 51, but the non-cali did....as soon as I put the other ECU in, I will check the codes again. If i don't get a 51, I will remove the f/p relay and see if it gets one then...any ideas?
#37
When I purchased my FD it did not boost at all and broke up all over the place. The symptoms were similar to yours. The car would idle fine but would buck, hesitate and stumble all over the place just driving around. The whole time it was the secondary injectors clogged to ****. I swapped them out with a friends and the car ran perfect and boosted great. Just something to check thats decently simple. Good luck.
#39
Original Gangster/Rotary!
iTrader: (213)
Right, but that still could be the problem. RC uses a varnish solution to clean the injectors, and (especially when they're not immediately installed) they can become stuck open or closed. I would take them out and apply voltage to them to see if they operate properly. Could very well be what's wrong.
#41
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
I will test out the wiring to the relay first and clear that. I will also put my cali ECU in and see if I can start the car...right now I can't get the car to even start...just cranks...
Trev
Trev
#42
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Okay, put the cali ECU back in...no code 51 anymore and it starts right up. The ECU I was trying was a 93 non-cali remanufactured ECU ( I assume replaced under a recall) Anyways, I connected voltage to the F/P and was getting 9.4 at idle and under light brisk acceleration, I was dipping to 8.8 or 8.9. I wiring a temporary direct wire from the battery to the red/white wire at the fuel pump and got 10.75 volts. I still have the stutter and hesistant doggy acceleration though. I only have a code 38 (AWS)...going to check BOTH fuel pump relays...I used a voltmeter/ohmeter on the fuel pump resistor and got 0.9 ohms which is 0.2 out of spec of the factory suggestion. I don't know if that is an error with the ohmeter though...I would need a flukemeter I would think to be totally accurate.
#44
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
I checked the circuit relay by applying voltage to terminals A and B and ohming out C and D. When I applied the voltage, it clicked like it should and it was registering 00.3 on the ohmeter. I need to get a second person to listen to the relay and make sure it is clicking when I turn the Ign on to verify the wiring is good going to it...after this, not sure where to turn...Is it possible that the filter ON the fuel pump can get clogged?
#45
Racecar - Formula 2000
#47
I had some funky problems on my last FD due to a bad wiring harness....
#48
Rotary Enthusiast
Thread Starter
iTrader: (4)
Join Date: Sep 2003
Location: Yutan, Nebraska
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Did you change your wiring harness when you did the motor? Given this and the low voltage you are seeing to the fuel pump, it almost sounds like serious electrical problems from an old, bad wiring harness.
I had some funky problems on my last FD due to a bad wiring harness....
I had some funky problems on my last FD due to a bad wiring harness....
#49
Yep, that is an expensive problem that many of us have encountered...
If you are checking fuel pressure, remember that the wiring might contribute to that. You might want to wire directly to the battery temporarily to help determine the cause of any fuel pressure issues you may be having.
Good luck.
If you are checking fuel pressure, remember that the wiring might contribute to that. You might want to wire directly to the battery temporarily to help determine the cause of any fuel pressure issues you may be having.
Good luck.