Where can I find these?
07-20-06, 06:10 PM
#1
I'm your turbo lover
Thread Starter
iTrader: (5)
Join Date: May 2006
Location: Marshfield, Massachusetts
Posts: 441
Likes: 0
Received 0 Likes
on
0 Posts
Where can I find these?
I'm looking for stock-diameter fiberglass front fenders, fiberglass rear hatch, fiberglass complete doors, and a carbon fiber hood like the one in the thumbnails. Anyone know where I can find 'em? I've been searching for the past 2hrs. Also, where can I find pulleys? I only need the crank, alternator, and water pump. There's a pic of one I found below, but the page was in Japanese.
07-24-06, 05:12 PM
#2
Former Moderator. RIP Icemark.
Unless you are driving a track only car, you will not want the pullies. They are not practical on a street driven vehicle.
And Mazdaspeed/ Mazda racing has them, as well as Racing Beat used to carry them.
and your bump has been deleted. Bumps are forbidden in the 2nd gen technical section.
And Mazdaspeed/ Mazda racing has them, as well as Racing Beat used to carry them.
and your bump has been deleted. Bumps are forbidden in the 2nd gen technical section.
Last edited by Icemark; 07-24-06 at 05:15 PM.
07-24-06, 06:36 PM
#3
FG fenders: ebay.......and I think corksport has them also.
NOTE: they are vented, but stock size and width.......however they fit about as well as my hand in a pringles tube (not good)
CF hood - speedmachine performance has a TII replica hood in carbon
doors? beats me..........all I can say though is, got bank?
rear hatch....no idea - I suggest PMing boostedrex, he might have a line on something
edit: and yeah....with that pulley set, at anything under about 2300 rpm you'll be running on battery and not flowing much coolant either, FAR to underdriven for street use.
NOTE: they are vented, but stock size and width.......however they fit about as well as my hand in a pringles tube (not good)
CF hood - speedmachine performance has a TII replica hood in carbon
doors? beats me..........all I can say though is, got bank?
rear hatch....no idea - I suggest PMing boostedrex, he might have a line on something
edit: and yeah....with that pulley set, at anything under about 2300 rpm you'll be running on battery and not flowing much coolant either, FAR to underdriven for street use.
07-25-06, 04:08 PM
#4
I'm your turbo lover
Thread Starter
iTrader: (5)
Join Date: May 2006
Location: Marshfield, Massachusetts
Posts: 441
Likes: 0
Received 0 Likes
on
0 Posts
I've looked on eBay, they all seem to be 20mm wider but I'll check again. That hood pictured is a wider hood to fit an RE Amemiya one-and-a-half intercooler (I think). I've seen the doors for $710 but I forget where and I've seen the hatch too, but I forget which site.
07-25-06, 04:25 PM
#5
Originally Posted by MazterDizazter
I've looked on eBay, they all seem to be 20mm wider but I'll check again.
Originally Posted by MazterDizazter
That hood pictured is a wider hood to fit an RE Amemiya one-and-a-half intercooler (I think).
Originally Posted by MazterDizazter
I've seen the doors for $710 but I forget where and I've seen the hatch too, but I forget which site.
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM