Wastegate question
#1
Wastegate question
on the WG i have it has two places for vacuum.
my question is, do both need to be used?
if not which one do i cap, if it even needs to be capped?
if i run both what do they go to
![scratch](https://www.rx7club.com/images/smilies/scratchhead.gif)
its a ebay wastegate; emusa, but ive looked at reviews, and it seems to be good.
and for nay-sayers, or anyone looking to just post bs, read signature.![Nod](https://www.rx7club.com/images/smilies/nod.gif)
thank you
EDIT: my pic didnt work so i googled
![](http://www.flashlinklive.com/wg.jpg)
EDIT: one vac port is on the top, the other is on the side
my question is, do both need to be used?
if not which one do i cap, if it even needs to be capped?
if i run both what do they go to
![scratch](https://www.rx7club.com/images/smilies/scratchhead.gif)
its a ebay wastegate; emusa, but ive looked at reviews, and it seems to be good.
and for nay-sayers, or anyone looking to just post bs, read signature.
![Nod](https://www.rx7club.com/images/smilies/nod.gif)
thank you
EDIT: my pic didnt work so i googled
![](http://www.flashlinklive.com/wg.jpg)
EDIT: one vac port is on the top, the other is on the side
Trending Topics
#11
ok, its been a while. somethings wrong..
had the 15lbs spring in there, and would get to it quick.
i swapped it out for a 5lbs so i could control 5psi up, buuut
i have my apexi avcr turned almost all the way up (2.0bar/ 80% duty) and its hardly making over 10psi......
i looked at the lines again,
COM is on the top of the WG
NC is split between side of WG and a nipple i put on the inercooler pipe.
ive looked at the apexi avcr external wastegate diagram over and over and compared it to what i have set up, and im lost.
any help would be great THANKS
had the 15lbs spring in there, and would get to it quick.
i swapped it out for a 5lbs so i could control 5psi up, buuut
i have my apexi avcr turned almost all the way up (2.0bar/ 80% duty) and its hardly making over 10psi......
i looked at the lines again,
COM is on the top of the WG
NC is split between side of WG and a nipple i put on the inercooler pipe.
ive looked at the apexi avcr external wastegate diagram over and over and compared it to what i have set up, and im lost.
any help would be great THANKS
#12
bump
still need help
the apexi avcr solinoid sometimes pulses..
i disconnect my screen and take it inside,because its been stollen 3 times already.
when i connect the screen/controller the solenoid pulses on and off (like a starter with a deadish battery)
buuut it only sometimes does this.. other times it connects with no problem
everything on the screen is reading the values correctly, but just cant make more the 11psi of boost, even with the controller set to 2.0BAR
any help would be great
Thanks
still need help
the apexi avcr solinoid sometimes pulses..
i disconnect my screen and take it inside,because its been stollen 3 times already.
when i connect the screen/controller the solenoid pulses on and off (like a starter with a deadish battery)
buuut it only sometimes does this.. other times it connects with no problem
everything on the screen is reading the values correctly, but just cant make more the 11psi of boost, even with the controller set to 2.0BAR
any help would be great
Thanks
Thread
Thread Starter
Forum
Replies
Last Post
Nosferatu
2nd Generation Specific (1986-1992)
7
09-05-15 02:13 PM