to4b 60-1 turbo-a little disappointed
10-16-06 | 12:51 AM
#27
you should probably post this in the single turbo section, but if I recall correctly, and I might be wrong on this. An FD ebay ssautoshit or similar manifold will work with an on center housing. They are about 100 bucks.
from: https://www.rx7club.com/showthread.p...4&page=1&pp=15
That FC just left our shop and yes the FD manifold will fit an FC chassis depending on what size turbo etc. Seems most common " medium" frame turbos will fit just fine. Only thing I noticed was wastegate position was less than desirable. That car was using an oncenter turbine housing, but it appears a tang will fit just fine.
10-18-06 | 07:16 PM
#29
Thread Starter
It's finally reliable
iTrader: (18)
Joined: May 2004
Posts: 3,513
Likes: 10
From: NEW YORK CITY
Originally Posted by calrx7
u dont need THAT much power man.. 350 whp is plenty
350hp is all i want,but i just wanna make sure its done the right way with the right stuff..
10-19-06 | 12:56 AM
#30
i spent more on tires...
Joined: Oct 2001
Posts: 1,686
Likes: 0
From: Oakland, CA
hey mob, i'm sorry you're disappointed in the turbo. please dont forgot it is a ball bearing turbo and with that hotside you will get power at very low rpms. depending on what kind of driving you do you may or may not want to get a bigger hotside. i think that combo is perfect for drifting, autocross, and daily driven. even at mid-high 300's you will be spanking a lot of cars out there.
speaking from experience, i run low boost @320whp everyday and its plently.
speaking from experience, i run low boost @320whp everyday and its plently.
10-19-06 | 06:59 AM
#31
pistons go home!
Joined: Sep 2006
Posts: 277
Likes: 0
From: switzerland
had a similar setup with my T60-1 but with a huge hotside, and that was quite annoying!! no real boost build up under 4000rpm!! after 5000rpm it pushed like hell but.... it isn't worth it i think... as far as street application is concerned
so i think you'll be lucky with a good responding early boostin' trubo
i'm going with BNR II
so i think you'll be lucky with a good responding early boostin' trubo
i'm going with BNR II
10-19-06 | 11:41 AM
#32
Joined: Dec 2001
Posts: 7,093
Likes: 121
From: Twin Cities, MN
Originally Posted by mobeoner
i dont understand what you said!....so my turbo housing it good or bad??
Oncenter vs tang
Last edited by Turblown; 10-19-06 at 11:46 AM.
10-19-06 | 12:40 PM
#33
if you can't find a hotside anywhere else I found one here http://www.wwrturboinjection.com/ for around 179 I believe. I
10-23-06 | 01:13 PM
#34
Senior Member
Joined: Dec 2005
Posts: 301
Likes: 0
From: Isabela pr
Originally Posted by 1Revvin7
Oncenter vs tang
Thanks
JP
PS: If you are wondering I have a 87 TII, if you need extra info let me know.
10-24-06 | 06:36 PM
#37
Thread Starter
It's finally reliable
iTrader: (18)
Joined: May 2004
Posts: 3,513
Likes: 10
From: NEW YORK CITY
i have been trying to do al little reaserch and it seems like the obx manifold that they sell on ebay can probably work with the on center turbo since the manifold falnge is higher that the hks manifold..is this right????
10-24-06 | 09:00 PM
#38
Burning up Time
Joined: Sep 2004
Posts: 805
Likes: 2
From: Earth
Originally Posted by mobeoner
i have been trying to do al little reaserch and it seems like the obx manifold that they sell on ebay can probably work with the on center turbo since the manifold falnge is higher that the hks manifold..is this right????
Thread
Thread Starter
Forum
Replies
Last Post
immanuel__7
2nd Generation Specific (1986-1992)
89
09-05-15 10:23 AM
