Testimonial for RA 3mm seals
#26
Lives on the Forum
Originally Posted by Karack
it didn't twist that much ya noob.
the lateral force cracked the pin slot, if it twisted that much all of the tension bolts would have snapped.
the lateral force cracked the pin slot, if it twisted that much all of the tension bolts would have snapped.
I tell you what...put together all the housings minus the e-shaft and the rotors.
Snug tension bolts but leave the dowel pins OUT.
$20 says you can twist the housings with the tensions bolts in there.
This is not a realistic example of of what forces can damage the dowel pin lands, but it gives you a good idea of the myth of what the tension bolts do.
The tensions bolts just keep the housings together, but they do NOT keep the housings from twisting relative to each other - that's the job of the dowel pins.
-Ted
#27
Super Raterhater
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,630
Likes: 0
Received 3 Likes
on
3 Posts
Ted: Do you have any input in general regarding 2mm vs 3mm without the dowel pin breaking? Since this is obviously turned into a more 2mm vs 3mm debate and general topic of such, I figured I might as well ask. Though, I am quite impressed that it's not too bad of a fight yet.
#29
What I want to know (a question not likely to be answered by anyone with the inside knowledge required) is why the rotary was designed, and worse yet, produced, with only 4 dowel pins. I mean, I'm not a structural engineer, but if I were looking at it from a design standpoint, knowing what forces act on an engine in a performance setting (as the rotary was/is marketed as), I would have probably thought to myself that there is no way 4 pins is enough to hold this entire engine together properly. I would have went with a *at least* 8, 1 on each corner of each half of the engine. It's obvious that their 4 pin design works, but it's not like it would have been any harder for them to design in 4 more pins for double the strength. There is plenty of room in the other 2 "corners" of teh block, with open/blank castings just sitting there serving no purpose.
#30
Senior Member
Join Date: Aug 2002
Location: BC, Canada
Posts: 555
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by RotaryResurrection
I guess let me put it another way. How many engines with mazda 2mm seals have you ever gotten that had cracked that rear iron dowelpin hole? I've never seen any at all. So, this leads me to believe that the mazda seals will break before the iron does. Yet, these 3mm seals did not break, while the iron did.
Raising hand...
2mm seals, rear iron cracked, in the same spot as your pics, except I lost the rears apex seals too...
#33
No, both rotor and rotorhousing are softer material than the iron which broke. As commonly seen, the rotor and/or housing would give first...plus there is only 2mm of seal thickness to cause problems, while most of these breaks show several mm of play.
#34
path of least resistance..the seals are new and strong..the iron is older and worn with posible stress fractures that were not visible during the rebuild...just a thought
Last edited by Travelintrevor; 04-08-05 at 04:06 AM.
#35
Lives on the Forum
Originally Posted by SonicRaT
Ted: Do you have any input in general regarding 2mm vs 3mm without the dowel pin breaking? Since this is obviously turned into a more 2mm vs 3mm debate and general topic of such, I figured I might as well ask. Though, I am quite impressed that it's not too bad of a fight yet.
I have never been a supporter of any of the aftermarket seals (well, can't afford $1,500+ Ianetti's!).
I truly believe is the stock Mazda OEM apex seals for almost any application.
I'll just leave it at that.
-Ted
#36
Senior Member
Join Date: Jun 2003
Location: Temple Tx
Posts: 276
Likes: 0
Received 0 Likes
on
0 Posts
does RA make a 2mm seal? If they're that strong then why not use 2mm for benefits of a better seal and less friction? I thought only reason for a 3mm was for strength to protect agaisnt detonation thats gonna happen on any street car. Like mine, just built 1500 miles and one night it creeped 2 psi what it was tuned for and I chipped a stock mazda seal. wouldn't a RA 2mm seal have held up and give you the best of both worlds?
#38
Why are we bumping this?
RA makes a 2mm seal...all you had to do was look?
http://www.rotaryaviation.com/2_mm_apex_seals.htm
Look at it this way.
The 2mm ra seals are made from their special alloy, and are X amount strong. The 3mm ra seals are made from the same material, but are now 1.5x times as strong. How is that hard to understand?
RA makes a 2mm seal...all you had to do was look?
http://www.rotaryaviation.com/2_mm_apex_seals.htm
Look at it this way.
The 2mm ra seals are made from their special alloy, and are X amount strong. The 3mm ra seals are made from the same material, but are now 1.5x times as strong. How is that hard to understand?
#39
Senior Member
Join Date: Jun 2003
Location: Temple Tx
Posts: 276
Likes: 0
Received 0 Likes
on
0 Posts
durr it's not lol but if a 2mm ra seal is stronger than say a regular 3mm seal then wouldn't it's be strong enough to handle most everyday situations and still have all the benefits of a 2mm seal. ie less wear and friction?
Thread
Thread Starter
Forum
Replies
Last Post