problem with n/a... help pls (shutting off)
09-21-06, 10:33 PM
#1
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
problem with n/a... help pls (shutting off)
hey guys not shure if you remember my previous but fuel pressure was reaching a 75 psi i cleaned out the return line and i replaced the factory FPR... car is still acting up heres the symptoms...
you turn on the car revs to about 2.5rpm and shuts right off no matter what you do even if you try to give it gas i checked everything i was thinking mayb a vacuum lines but everything is connected any ideas??? please need the help
Thanks
TwEaK
you turn on the car revs to about 2.5rpm and shuts right off no matter what you do even if you try to give it gas i checked everything i was thinking mayb a vacuum lines but everything is connected any ideas??? please need the help
Thanks
TwEaK
Trending Topics
09-22-06, 02:44 PM
#9
Strength and Honor
Join Date: Apr 2006
Location: CA bay area
Posts: 391
Likes: 0
Received 0 Likes
on
0 Posts
Oops, you said "when you turn the car on," not "when you turn the car"! I misread that. When you first turn the car on it should rev to 3k, not 2.5k. Are you positive you don't have a vacuum leak? Is this a rebuild or swap project?
Check here for an idle system overview
and here for idle troubleshooting
Check here for an idle system overview
and here for idle troubleshooting
09-22-06, 04:16 PM
#10
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
this is the original motor car was running fine started getting worse over time until it finally came to the point you cant drive the car.... it just goes to 2.5k rpm and boom its like if i turned off the car.... one of the reason why i take away vacuum leak because even with a vacuum leak pushing down on the throttle will keep the car running... but in this case i touch the throttle car shuts right off
TwEaK
TwEaK
09-22-06, 04:20 PM
#11
Rotary Enthusiast
Join Date: Jul 2004
Location: Lubbock,Tx
Posts: 881
Likes: 0
Received 0 Likes
on
0 Posts
Well I was just fighting the same problem.
Ended up being one of the intake gaskets so I just replaced both. Fixed the problem right up.
Now I am just left with a surging idle but it stays running.
Might also check your TPS
Mike
Ended up being one of the intake gaskets so I just replaced both. Fixed the problem right up.
Now I am just left with a surging idle but it stays running.
Might also check your TPS
Mike
09-22-06, 05:12 PM
#12
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
ill check out the intake gaskets but TPS was just replaced.. just for the hell of it any other ideaS?? where are the smart guys lol??? icemark?aaron?NZ convertible?? cmon lol
TwEaK
TwEaK
Thread
Thread Starter
Forum
Replies
Last Post
Adaptronic 1280s Hot Start 3 Rotor 20b RX7
Monsterbox
Adaptronic Engine Mgmt - AUS
5
09-11-15 03:29 PM
rx8volks
Canadian Forum
0
09-01-15 11:02 PM
rx8volks
Canadian Forum
0
09-01-15 10:46 PM