No bigger injectors then 780cc's...?
#1
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
No bigger injectors then 780cc's...?
Ok, i called my local ( only ) rotary shop here in calgary and they are telling me that there are no injectors for my car past 720cc's, ( 780cc custom made ), i called complete BS when i heard this, i want/need 860cc's and they are telling me there are none for my car, wtf...?
i have an 1989 S5 turbo, S4 T2 block with all S5 externals....
anyone know where i can get the injectors i need?...
thanx....
P.S. need a direct bolt-in style....
i have an 1989 S5 turbo, S4 T2 block with all S5 externals....
anyone know where i can get the injectors i need?...
thanx....
P.S. need a direct bolt-in style....
#2
No money. No love.
iTrader: (12)
Join Date: Jul 2004
Location: SACRAMENTO
Posts: 2,807
Likes: 0
Received 0 Likes
on
0 Posts
http://cgi.ebay.com/ebaymotors/PTE-D...QQcmdZViewItem
these fit into my secondary position fine. Hondahater...or Iliketoeatricers gave me the idea. Not sure which of the two =/ They told me that the grommet would be squished a bit...but it works fine. I have mine in and they fit the secondary rail. (I bought 2) Haven't tried primary.
these fit into my secondary position fine. Hondahater...or Iliketoeatricers gave me the idea. Not sure which of the two =/ They told me that the grommet would be squished a bit...but it works fine. I have mine in and they fit the secondary rail. (I bought 2) Haven't tried primary.
#3
Super Raterhater
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,630
Likes: 0
Received 3 Likes
on
3 Posts
I think they're telling you there are no stock replacement high imp injectors that large. The ones most people use are low-imp square connectors (you have oval). What you do is hack off your connectors, solder on the square ones, then solder in resistors at the ECU, and you can use larger (890, 1600, whatever)
#4
I R SAD PANDA W/O BAW
If you know they exist why dont you just search or look at other people's setups?
If you want to get technical if you have an s5 harness with the oval injector connector plugs nothing will be direct bolt in because most high CC injectors are low impedence (require soldering resistors) and also most are bosch style plug (square connector) so you will need to solder those also.
Basically any top feed injector that can fit a DSM or honda will work, some may require slight modification to fit into the rails. Search for 1600cc injector modification and I'm sure you'll find some write ups. Personally I used 1000cc PTE injectors and they went in no problem.
EDIT: looks like all 3 of us posted at once
If you want to get technical if you have an s5 harness with the oval injector connector plugs nothing will be direct bolt in because most high CC injectors are low impedence (require soldering resistors) and also most are bosch style plug (square connector) so you will need to solder those also.
Basically any top feed injector that can fit a DSM or honda will work, some may require slight modification to fit into the rails. Search for 1600cc injector modification and I'm sure you'll find some write ups. Personally I used 1000cc PTE injectors and they went in no problem.
EDIT: looks like all 3 of us posted at once
Last edited by ilike2eatricers; 08-02-05 at 10:31 PM.
#5
tom port.. AKA streetport
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
what about 3rd gen.
https://www.rx7club.com/showthread.php?t=449773
now will these require a dif. connector for my s4 high imp. ive never looked into this yet.
https://www.rx7club.com/showthread.php?t=449773
now will these require a dif. connector for my s4 high imp. ive never looked into this yet.
Trending Topics
#9
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
i got these, my friend had them when he owned my RX7 and he said they were 720cc's....
but these are the wrong imped for my car, i know the resistor thing, but do these look like they would work?...
they are DENSO by the way....
and incase someone didnt read or skipped over, i have an S4 T2 block with S5 T2 externals....
( Had to take the pic in the bathroom, enough light for my shitty cam.... )
but these are the wrong imped for my car, i know the resistor thing, but do these look like they would work?...
they are DENSO by the way....
and incase someone didnt read or skipped over, i have an S4 T2 block with S5 T2 externals....
( Had to take the pic in the bathroom, enough light for my shitty cam.... )
#11
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,791
Likes: 0
Received 114 Likes
on
96 Posts
Originally Posted by Archangels
Ok, i called my local ( only ) rotary shop here in calgary
and they are telling me that there are no injectors for my car past 720cc's, ( 780cc custom made ), i called complete BS when i heard this, i want/need 860cc's and they are telling me there are none for my car, wtf...?
#12
Rotary Enthusiast
Join Date: May 2005
Location: Vernon, BC
Posts: 1,135
Likes: 0
Received 0 Likes
on
0 Posts
I didnt really want to start a new thread so ill jsut ask it here.. what kind of benifits do you gain from bigger injectors? say I was to go with 720cc injectors with the stock ecu and stuff. would it do anything but hurt my gas mileage?
#14
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
yep RX7 Specialties, for some reason every time i call them they are far more expensive then everyone else and try to sell me something i dont need....
thanx though aaron, does anyone have an idea about those injectors though...?
thanx though aaron, does anyone have an idea about those injectors though...?
#15
tom port.. AKA streetport
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
im guessing youre refering to the low imp. 720's which they all are. youd need to solder in resistors next to the ecu and solder in dif. plug connectors from what im gathering. dont quote me on this cause im about as far on this as you are. if ya want to part with those 720's gimme a pm^^^^^
#16
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
hmm, well i'll see how hard it is too install these, ofcourse i have to go to RX7 specialties....
* sigh *
if i dont end up using them i'll tell ya....
* sigh *
if i dont end up using them i'll tell ya....
#17
tom port.. AKA streetport
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
i really dont think its that hard. go to radio shack ask for resistors, 10ohm/10watt purchase of 2 part# 271-132. these wire into the ecu for the injectors and then you do the same for youre connectors. it might take a little time but i think its possible. you might not even need the connectors but someone on hear that knows will tell ya.
#18
tom port.. AKA streetport
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Archangels
hmm, well i'll see how hard it is too install these, ofcourse i have to go to RX7 specialties....
* sigh *
if i dont end up using them i'll tell ya....
* sigh *
if i dont end up using them i'll tell ya....
#19
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
wow, with those part numbers i can get them cheap!...
RX7 specialties was about to charge me $14 EACH.... and thats not to install them eithe!... ( $30 )....
RX7 specialties was about to charge me $14 EACH.... and thats not to install them eithe!... ( $30 )....
#20
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,791
Likes: 0
Received 114 Likes
on
96 Posts
Originally Posted by Archangels
wow, with those part numbers i can get them cheap!...
RX7 specialties was about to charge me $14 EACH.... and thats not to install them eithe!... ( $30 )....
RX7 specialties was about to charge me $14 EACH.... and thats not to install them eithe!... ( $30 )....
BTW, you do have something to control those larger injectors, right? Just putting them in place of your secondaries is going to make the car run super rich whenever the secondaries kick in.
#21
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
i have a PFC Fcon right now and an SAFC-II ready to be installed....
i'm a little afraid of installing the SAFC-II though, i dont want to install it and all the sudden run lean with the 720's or something freaky like that....
i was thinking i should install it, let the car sit for a week or so till i can get on the dyno....
unless ofcourse the great Aaron can share his wisdom using the SAFC!...
:P
i'm a little afraid of installing the SAFC-II though, i dont want to install it and all the sudden run lean with the 720's or something freaky like that....
i was thinking i should install it, let the car sit for a week or so till i can get on the dyno....
unless ofcourse the great Aaron can share his wisdom using the SAFC!...
:P
#22
I R SAD PANDA W/O BAW
Originally Posted by Archangels
i have a PFC Fcon right now and an SAFC-II ready to be installed....
i'm a little afraid of installing the SAFC-II though, i dont want to install it and all the sudden run lean with the 720's or something freaky like that....
i was thinking i should install it, let the car sit for a week or so till i can get on the dyno....
unless ofcourse the great Aaron can share his wisdom using the SAFC!...
:P
i'm a little afraid of installing the SAFC-II though, i dont want to install it and all the sudden run lean with the 720's or something freaky like that....
i was thinking i should install it, let the car sit for a week or so till i can get on the dyno....
unless ofcourse the great Aaron can share his wisdom using the SAFC!...
:P
#24
- Make Haste -
Thread Starter
Join Date: Apr 2005
Location: Calgary, Alberta
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ilike2eatricers
Sounds like you're in over your head concerning some of these modifications. Everything has been posted concerning these mods before you just need to research more. If you install the SAFC and dont adjust any of the corrections it will be like it's not even installed. Not trying to knock you or anything but you need to do some more research first.
i'll get it installed and tuned within' dayz i guess, will be the best bet....
#25
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,791
Likes: 0
Received 114 Likes
on
96 Posts
A non-tuned S-AFC is exactly like having none installed. If all the corrections are set to zero, then the fuel map is unchanged.
Remember, if you get an S-AFC, you need to have it tuned. This involves a bit of investment, since it likely will take an hour or so on the dyno and a wideband.
Remember, if you get an S-AFC, you need to have it tuned. This involves a bit of investment, since it likely will take an hour or so on the dyno and a wideband.