NMJ87T2

iTrader: (8)

I have not had a lot of time to work on the 7 today, but I did get a little bit done.

lchaidez

iTrader: (4)

i cant stop my jaw from dropping. this is lookin fantastic!

MazterDizazter

iTrader: (5)

Agreed!

NMJ87T2

iTrader: (8)

I have been working on getting the fuel lines hooked up today. More to come later when it is done.

NMJ87T2

iTrader: (8)

Thanks for all of the compliments guys!

FC3sBoosted

why hadnt i seen this thread till now??? that is beautiful, very nice work man, very.

ColdSeven

looks real good can't wait to redo my Jspec this winter.

NMJ87T2

iTrader: (8)

Here is the fuel system completed. I need to get a few more fittings to get all an fittings on all ends.

lax-rotor

iTrader: (1)

How did you mount the intercooler, or is it supported only by the piping?

88rxn/a

iTrader: (6)

fantastic work!!

Digi7ech

iTrader: (1)

Oh man,
My wallet is hurting just looking at all that SS/AN fuel line and adapters.

Defintely sexy though

What FPR are you using? I'm still trying to find one that's under the $135 Aeromotive price tag.

PS. Paint that Oil fill tube!

NMJ87T2

iTrader: (8)

It is a SARD rising rate fpr. I think I got it from www.rx7.com ? It was a little cheaper than the aeromotive. I have an exhaust for you too.

NMJ87T2

iTrader: (8)

I have been busy this rvrning working on my intercooler piping. I have a few more pieces to cut an then weld up and I will be done with it.

lchaidez

iTrader: (4)

im not sure if this was already mentioned but, how much have you spent on this project/car and how much time, sweat, and blood has this taken from you?

it looks really clean! Have considered doing the Miata tranny swap?

*jaw is still dropping*

NMJ87T2

iTrader: (8)

Thanks for your compliments.
I do not even care to think about all of the time, sweat, blood, aggravation, sleepless nights, and money has gone into it as of right now. All of them are substantial though. Keep posted for more updates!

adrock3217

Maybe I've been out of the loop for a little too long..but..why would he do a Miata transmission swap?

djmtsu

iTrader: (3)

He wouldn't.

classicauto

iTrader: (3)

Geez n00b, don't you know miata transmissions titanium?

lchaidez

iTrader: (4)

it was just a suggestion. I've seen people do them and I've always heard positive feedback from it. I figured he'd be interested or already looked into it. Apparently not, but eh. I'll keep checking in.

Oh and hey I got my Blackmagic Fan to turn on, but it only turns on when the engine temp is really high. Didnt have time to work on it some more, but in my book it seems i've accomplished alot. Im sure with what you have done you'll figure it out and I'll keep posted.

I just wish I had a garage... maybe in the next couple of months, *sigh*

NMJ87T2

iTrader: (8)

No, I have never even considered a miata tranny. I have heard about people swapping out the gear sets though.

NMJ87T2

iTrader: (8)

I finished putting the exhaust on today. It is a custom 3" down pipe that is ceramic coated and has an egt bung and o2 sensor bung. It is mated up to a Corksport 3" catback.

88rxn/a

iTrader: (6)

your a mad working fool!!!
i love it!!
what kind of exhaust manifold you runnin?
and is that a 45 degree bend on your DP?

NMJ87T2

iTrader: (8)

I know I am a fool!lol The exhaust mani is a custom job. It is shaped after the hks log mani, but it it 2.5" 321ss construction. Yeah, the dp goes down at about a 45 degree angle.

Thanks

Aaron Cake

iTrader: (1)

Just a suggestion, but you're going to want to heat wrap the front half of the exhaust system. The reduction in underhood temps (as well as floor temperature!) is dramatic.

Digi7ech

iTrader: (1)

Downpipe looks coated so it may be fine