My Bonez Race pipe arrived in the mail today
04-02-02, 11:05 PM
#26
Senior Member
Join Date: Feb 2001
Location: Winter Springs, FL
Posts: 261
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by bcty
nevermind i think i got it.. it was a small hose connected to the pressure sensor i must have hit out!!... anyways do i really need a block off plate when i remove my air pump?
nevermind i think i got it.. it was a small hose connected to the pressure sensor i must have hit out!!... anyways do i really need a block off plate when i remove my air pump?
No not relay bu tI jsut dont like the Idea of an unfiltered hole leading to the engine (the on ethat the air pump hose conected to). Although it feels like ait come OUT of it. I'm gona order my block of palte this week so I can remove the ACV that is taking up space.
04-03-02, 12:24 AM
#27
Boost This!
Thread Starter
Join Date: Nov 2001
Location: Nanaimo, B.C, Canada
Posts: 1,935
Likes: 0
Received 0 Likes
on
0 Posts
yeah i wanna do that too... how hard is ti to make one though.. i have a few good friends that are good at stuff like that? can anybody gimme a pic of what one looks like?
04-03-02, 01:07 AM
#28
Senior Member
Join Date: Feb 2001
Location: Winter Springs, FL
Posts: 261
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by bcty
can anybody gimme a pic of what one looks like?
can anybody gimme a pic of what one looks like?
Here is a site that shows it, click on the air control valve link.
http://home.earthlink.net/~burntoast/6port.html
The block off plates can be found at www.mazdatrix.com
do a search on it.
04-03-02, 01:25 AM
#29
Boost This!
Thread Starter
Join Date: Nov 2001
Location: Nanaimo, B.C, Canada
Posts: 1,935
Likes: 0
Received 0 Likes
on
0 Posts
i was just curious.. hopefully i can get an awnser before tonight... but sice i am getting my exhaust installed at the shop.. i cant dissamble the air pump there can i just take off the belt and will it be ok?
04-03-02, 01:11 PM
#33
Full Member
Join Date: Jan 2002
Location: NB, Canada
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
carefully back your car up into your room beside the computer desk. WATCH OUT FOR THE MIRRORS! let the computer mic hang down low as close to the pipe as possible... blip the throttle a few times and record 10 seconds or so of idle and revving... then carefully drive your car back out of the house...
sorry. i had to.
record it on cassette if you have to. plug the stereo into the line in on your sound card. capture the audio with any software you can find on tucows for free. save it as a wav file.
sorry. i had to.
record it on cassette if you have to. plug the stereo into the line in on your sound card. capture the audio with any software you can find on tucows for free. save it as a wav file.
04-03-02, 05:34 PM
#34
Boost This!
Thread Starter
Join Date: Nov 2001
Location: Nanaimo, B.C, Canada
Posts: 1,935
Likes: 0
Received 0 Likes
on
0 Posts
i see... i just have to say... i just got my exhaust on... ohhhh myyyyy goooooooooood........... sweeeeeeet... i will get a clip up for you soon!!
04-03-02, 05:48 PM
#35
Eat, sleep, work, mod.
Join Date: Jun 2001
Location: Long Island
Posts: 2,517
Likes: 0
Received 0 Likes
on
0 Posts
Question, if the rods on the actuators are stuck are the ports stuck and if so how does one open them? Hammer down the rods? 
haha let me know please...
haha let me know please...
04-03-02, 08:35 PM
#38
Boost This!
Thread Starter
Join Date: Nov 2001
Location: Nanaimo, B.C, Canada
Posts: 1,935
Likes: 0
Received 0 Likes
on
0 Posts
i got the sound clips if anyone wants me to email it to them so they can host it!!! i have an decent idel and a bit of a drive... they area a bit distorted becuase it was picking up wind noise!! you can get the idea though... someone wanna host!! and its very loud.. it shakes the mic and distortes it!!
"really?? anyone else done it before? just seems to easy, ya know..."
if yours are stuck closed then try lubeing them before u hammer them....
"really?? anyone else done it before? just seems to easy, ya know..."
if yours are stuck closed then try lubeing them before u hammer them....
04-03-02, 08:40 PM
#39
Full Member
Join Date: Jan 2002
Location: NB, Canada
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
I'll host, even though it isn't the fastest connection. Send them my way. Do you have MSN? My email (exchange) server is temporarily down so peer to peer is easier. If the clip isn't too big (less than 1 meg) send it to blake.obrien@eudoramail.com
04-03-02, 09:03 PM
#40
Full Member
Join Date: Jan 2002
Location: NB, Canada
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
http://unb-icar.myip.org/drive1.mp3 --1.2meg
http://unb-icar.myip.org/drive2.mp3 -- 358k
http://unb-icar.myip.org/drive3.mp3 -- 857k
http://unb-icar.myip.org/idle.mp3 -- 137k
Any problems, let me know.
http://unb-icar.myip.org/drive2.mp3 -- 358k
http://unb-icar.myip.org/drive3.mp3 -- 857k
http://unb-icar.myip.org/idle.mp3 -- 137k
Any problems, let me know.
04-03-02, 11:51 PM
#41
Boost This!
Thread Starter
Join Date: Nov 2001
Location: Nanaimo, B.C, Canada
Posts: 1,935
Likes: 0
Received 0 Likes
on
0 Posts
sorry for the quality the wind interferred... it does not sound like a lawnmower at all thats just the wind.. its real loud and just perfect!! i love the way it sounds!! tons of looks!! let me know how it sounds on other computers!! thanks
Last edited by bcty; 04-03-02 at 11:56 PM.
05-14-02, 07:32 PM
#42
Boost This!
Thread Starter
Join Date: Nov 2001
Location: Nanaimo, B.C, Canada
Posts: 1,935
Likes: 0
Received 0 Likes
on
0 Posts
just got a pic.. if anyone cares... that mic really sucked.. just a standard computer mic... im proud of my single
https://www.rx7club.com/forum/attach...&postid=671694
https://www.rx7club.com/forum/attach...&postid=671694
Thread
Thread Starter
Forum
Replies
Last Post
rx8volks
Canadian Forum
0
08-13-15 04:55 AM
