installing headers?
#1
Banned. I got OWNED!!!
Thread Starter
Join Date: Mar 2003
Location: Bloomington, IN
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
installing headers?
is it that hard to install headers?
what all do i need? when i buy them do they come with everything i need?
do i need a torque wrench?
whats a good way to prop the car up?
will i see clearly what needs to be done when im under the car?
what all do i need? when i buy them do they come with everything i need?
do i need a torque wrench?
whats a good way to prop the car up?
will i see clearly what needs to be done when im under the car?
#2
RIP Icemark
iTrader: (4)
Very easy (except old rusted exhaust bolts)Use Jackstands, don't have to use a torque wrench but I would recomend it. If you have half a brain it will be obvious what you need to do.
And a little hint- get some really good penetrating oil and spray that on the exhaust nuts/bolts, and let it sit for a while, then spray them again then try taking them off.
And a little hint- get some really good penetrating oil and spray that on the exhaust nuts/bolts, and let it sit for a while, then spray them again then try taking them off.
#5
Banned. I got OWNED!!!
Thread Starter
Join Date: Mar 2003
Location: Bloomington, IN
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
well, im assuming you could get these at like autozone or somthing? i just know what they are. i was trying to figure out a way to get the block things under the wheels but it seems too low, is it?
Trending Topics
#11
Banned. I got OWNED!!!
Thread Starter
Join Date: Mar 2003
Location: Bloomington, IN
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
i have a hydrolic pump but its seems too dangerous to get under the car with only that....what could i put under the wheels after pumping the car up? anyone have any suggestions
#13
I wanta be with the BUC!
Join Date: Jan 2003
Location: Knoxville, TN
Posts: 2,305
Likes: 0
Received 0 Likes
on
0 Posts
Wow, I don't really even know were to start on this thead. Let me tell you if you can't install a header, you are border line retarded. I can understand a little bit of a delay from a broken stud that holds the exhaust manifold on, but other than that. Youshould have no trouble. And I am even more dumbfounded taht you don't know what jack stands are. Do you know were the jack in you car is??? Some how I dought you do, but if you do, to get those "little block thingies" under your tires you can use you jack. Wow, now I know why my automechanics teacher was teaching really stupid stuff like how to put jack stands under the car. I never really thought that there were people that didn't know how to use them, I always thought it was comon sense.
#14
Back from the dead...
Join Date: Feb 2003
Location: Calgary
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
You dont know what jackstands are, you dont know how to use a jack to lift your car. For safety purposes i suggest having someone there who has used jackstands so the car doesnt fall on you.
#15
Banned. I got OWNED!!!
Thread Starter
Join Date: Mar 2003
Location: Bloomington, IN
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
ok, first thing, i have never seen a jackstand before, im not a retard. second thing, i know where the jack is, but the question is can i get wheel blocks under the wheels with the jack, is it tall enough. if so, that solves my problem, and i guaranty that if i saw a jack stand i would know how to use it. the reason i started this thread is becuase i told my brother i was getting headers and he thought it was hard as hell to install them.since i havent had a chance to get under the car and look, i wanted to ask you. you guys dont have to be such ******** to me because i just havent happened to use or see a jackstand before, that doesnt make me stupid. it makes me ignorant to jack stands.
#18
I wanta be with the BUC!
Join Date: Jan 2003
Location: Knoxville, TN
Posts: 2,305
Likes: 0
Received 0 Likes
on
0 Posts
Well I would suggest to use concrete blocks (they cost like 20 cents a piece at home depot new) and use them insteed of jack stands. Jack stands will mess the little flang up that your car jack uses. If you use concrete blocks I think they are much safer to, because thr car is still on it's tires. I really thought it was very dangerous when I put my car on juack stands, and I feel much safer when it is on concrete blocks.
#19
Banned. I got OWNED!!!
Thread Starter
Join Date: Mar 2003
Location: Bloomington, IN
Posts: 359
Likes: 0
Received 0 Likes
on
0 Posts
you only use one wheel block and the jack? or jack it up and put the wheel block on the opposite wheel first? and is there any other thing to take the place of a wheel block? i will be pressed for money after i get my top speed cat back. also, are there and flanges or rings i need to use for the headers, or will everything i need come with it?
#20
All the hardware should come with the header. Just make sure you buy the appropriate presilencer or have a pipe made to fit between the header and the cat back. You might also need a new engine to header gasket, can't remember what gasket comes with and which you have to buy extra.
In all honesty, if you're going to be working on your car a lot, invest in some basic tools before loading on the mods. You can always use the spare tire jack, but I'd suggest a good floor jack and a set of jackstands. Check Sears or any auto parts store.
In all honesty, if you're going to be working on your car a lot, invest in some basic tools before loading on the mods. You can always use the spare tire jack, but I'd suggest a good floor jack and a set of jackstands. Check Sears or any auto parts store.
#22
I wanta be with the BUC!
Join Date: Jan 2003
Location: Knoxville, TN
Posts: 2,305
Likes: 0
Received 0 Likes
on
0 Posts
I'm telling you use cement blocks, they are much cheaper, and you don't have to be on pavement or concrete to use them like you do with jack stands. And the gasket that came with my road race heaser was the one inbetween the header and were the presilencers would go. Wow, your going to have like $800 bucks ties up into an exhaust system and I should only have about $250-300, since I am makeing my own side exit exhaust. It will be great all I have to do is mail the money to spintech mufflers tommorrow, and then put it all together.
And also did you order a single or a road race header. Because I remember a while ago that you were talking about this and they told you to get a road race header, and I am just wanting to clariffy that unless you are using a true dual system that you will have to buy or make a collector to bolt to your header if you bought a road race header.
And also did you order a single or a road race header. Because I remember a while ago that you were talking about this and they told you to get a road race header, and I am just wanting to clariffy that unless you are using a true dual system that you will have to buy or make a collector to bolt to your header if you bought a road race header.
#24
Zoom Zoom Boom!
Join Date: Mar 2003
Location: San Francisco, CA
Posts: 2,312
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by steve's dog
you only use one wheel block and the jack? or jack it up and put the wheel block on the opposite wheel first? and is there any other thing to take the place of a wheel block? i will be pressed for money after i get my top speed cat back. also, are there and flanges or rings i need to use for the headers, or will everything i need come with it?
you only use one wheel block and the jack? or jack it up and put the wheel block on the opposite wheel first? and is there any other thing to take the place of a wheel block? i will be pressed for money after i get my top speed cat back. also, are there and flanges or rings i need to use for the headers, or will everything i need come with it?
I would HIGHLY recommend you find someone else that knows his way around working on cars. Judging from your post, I'd hate to see you get crushed under the car from setting up the car improperly to work on.
#25
mad scientist
"The problem with America is stupidity. I'm not saying there should be a capital punishment for stupidity, but why don't we just take the safety labels off of everything and let the problem solve itself?"
That quote comes to mind after reading this thread...
That quote comes to mind after reading this thread...