idle
#1
Junior Member
Thread Starter
Join Date: May 2002
Location: kansas
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
idle
i have an 87 turbo II with a 91 turbo on it and the air pump is gone. i put a cover plate over where the valve was and now the ilde bounces from 700 to 1300 rpm. the tps is brand new. would anyone happen to know i can do to fix it?
#2
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Block off plate leaking a bit maybe. Weak guess. The cycling idle.....did it start after the new turbo or after the acv was removed???? One of those hose that went to the acv was a vacuum, the other two were more than less pressure. Is the one that was vacuum *switching solenoid*, not plugged???? The hose that is.
#5
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure none of the three vac hose that were removed from it are leaking a
#7
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure
Trending Topics
#8
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure none of the three vac hose that were removed
#9
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure none of the three
#10
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure none of the
#12
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure none of hte
#13
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make sure none of the three vac
#14
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 22 Likes
on
20 Posts
Spray some starter fluid around the acv blockoff plate and see if the idle changes in tone. If it does, then rip it off and use some more rtv as a gasket next time. Also check and make
Thread
Thread Starter
Forum
Replies
Last Post
LongDuck
1st Generation Specific (1979-1985)
12
10-07-15 08:12 PM