RX7Club.com - Mazda RX7 Forum

2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:
Banzai Racing

got my injectors cleaned.... now gas is going everywhere?

Thread Tools
 
Search this Thread
 
Old 08-30-03, 03:24 PM
  #1  
Rotor Nut.

Thread Starter
iTrader: (34)
 
Join Date: Feb 2002
Location: RI
Posts: 2,163
Likes: 0
Received 2 Likes on 2 Posts
got my injectors cleaned.... now gas is going everywhere?
got my injectors cleaned at a local shop and now i put them back on and gas is going all over the place and the car wont stay on. do i need new o-ring seals for the injectors? or are they installed wrong? what could it be. any help appreciated.
smg944 is offline  
Reply Like
Old 08-30-03, 03:26 PM
  #2  
Eat Rice Don't Drive it.

iTrader: (3)
 
1987RX7guy's Avatar
 
Join Date: Nov 2002
Location: Laredo, Tx
Posts: 12,752
Likes: 0
Received 1 Like on 1 Post
Get new O-rings and grommets.
1987RX7guy is offline  
Reply Like
Old 08-30-03, 03:28 PM
  #3  
holley guy

 
mwatson184's Avatar
 
Join Date: Feb 2003
Location: K.C. MO
Posts: 898
Likes: 0
Received 1 Like on 1 Post
^yep always replace orings when replacing injectors.

-Marques
mwatson184 is offline  
Reply Like
Old 08-30-03, 03:29 PM
  #4  
Alcohol Fueled!

iTrader: (2)
 
J-Rat's Avatar
 
Join Date: Jan 2002
Location: Hood River oregon
Posts: 11,093
Likes: 0
Received 2 Likes on 2 Posts
And pressure test your system before installing the intakes!!!
J-Rat is offline  
Reply Like
Old 08-30-03, 03:29 PM
  #5  
Rotorhead

 
Evil Aviator's Avatar
 
Join Date: Feb 2001
Location: Charlottesville, Virginia, USA
Posts: 9,136
Likes: 0
Received 39 Likes on 33 Posts
It's amazing what you can learn if you read the service manual.
Evil Aviator is offline  
Reply Like
Old 08-30-03, 03:29 PM
  #6  
Rotor Nut.

Thread Starter
iTrader: (34)
 
Join Date: Feb 2002
Location: RI
Posts: 2,163
Likes: 0
Received 2 Likes on 2 Posts
how do i pressure test it? start it with no intakes?
smg944 is offline  
Reply Like
Old 08-30-03, 03:34 PM
  #7  
pei > caek

 
dr0x's Avatar
 
Join Date: May 2002
Location: Mars
Posts: 4,643
Likes: 0
Received 0 Likes on 0 Posts
Jumper the yellow plug at the passanger strut tower and turn the key to ON.
dr0x is offline  
Reply Like

Trending Topics

Old 08-30-03, 03:34 PM
  #8  
Alcohol Fueled!

iTrader: (2)
 
J-Rat's Avatar
 
Join Date: Jan 2002
Location: Hood River oregon
Posts: 11,093
Likes: 0
Received 2 Likes on 2 Posts
Well, I install the primaries... Then I install the secondaries with tie-straps. Then I use the fuel pump test connector (with the fuel lines hooked up obviously), to pressurize the system to look for leaks.
J-Rat is offline  
Reply Like
Old 08-30-03, 03:42 PM
  #9  
Engine, Not Motor

iTrader: (1)
 
Aaron Cake's Avatar
 
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,791
Likes: 0
Received 114 Likes on 96 Posts
When you install the new o-rings and grommits, coat them with vascelene or other thick lubricant. This will keep them from being torn up as you push the injector into the fuel rail.
Aaron Cake is offline  
Reply Like
Old 08-30-03, 03:44 PM
  #10  
Rotor Nut.

Thread Starter
iTrader: (34)
 
Join Date: Feb 2002
Location: RI
Posts: 2,163
Likes: 0
Received 2 Likes on 2 Posts
i rewired my fuel pump any thing diffrent i should do or not do?
smg944 is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Power FC Idles rich, leans out and dies pushing throttle.
barkz
Power FC Forum
37
11-21-20 09:34 AM
Power FC Injector setup Question
bryancmatthews
Power FC Forum
0
09-05-15 03:57 PM
Back to Subforum
2nd Generation Specific (1986-1992)
View Next Unread
Testing the rad cap?




Advanced Search
Quick Reply: got my injectors cleaned.... now gas is going everywhere?


Reply Closed Thread Share

All times are GMT -5. The time now is 12:35 AM.