Originally Posted by Icemark
(Post 7422406)
Then that points to either a bad motor or a pinched wire.
If you meter the Grn/Wht does it rest at a perfect ground or does it have a couple of ohms of resistance? Black/white is 12 V Green/white is close Red/white is open (this is a vert SANS airbag) Is there a way to manally raise this thing? |
Originally Posted by J-Rat
(Post 7427081)
Is there a way to manally raise this thing?
|
Serious?
And where is the E-brake switch, by the e-brake? |
1 Attachment(s)
Originally Posted by J-Rat
(Post 7427106)
Serious?
And where is the E-brake switch, by the e-brake? And are you sure about those wires??? https://www.rx7club.com/attachment.p...1&d=1192581821 |
Yeah, as I read that, B/Y is your 12V feed.
R/W is open, G/W is close. Black is ground, and the light green is warning... Unless I am reading it all wrong. |
IceMark im just wondering why you say you stay away from S5's at all cost, just curious.
OP, when i first bought my s5 vert the motors were shot so I disconnected the main lift arms, and just lifted it up and down whenever i needed to, wasn't bad at all, but with new motors its just so neat to have it go up and down on its own. Matt |
I pulled up the carpet around the E-brake and found a sensor. If i Messed with it in made the brake light on the dash flicker. Same sensor?
|
So me and the wife just went and pulled on it with everything we had.. It wont budge.
|
Originally Posted by J-Rat
(Post 7427148)
I pulled up the carpet around the E-brake and found a sensor. If i Messed with it in made the brake light on the dash flicker. Same sensor?
Ground the wire at the sensor, it sounds like your top should work after that |
Oh, the light is on, top still wont work. LIke i said, we just cranked on it with everything we had.. It wont budge from the downzors position.
|
Originally Posted by J-Rat
(Post 7427190)
Oh, the light is on, top still wont work. LIke i said, we just cranked on it with everything we had.. It wont budge from the downzors position.
|
Even from the Diag plug. No beeping, nothing. It doesnt even load down the system.
If I can get to the LH motor maybe I can make sure the 12 V is coming down the G/W line? |
Crap...
Judging from the looks of it I am screwz0red unless I can get that damn top up... |
Yeah, that would be my next step... going to the motors, disconnecting them and seeing if I can pop up the roof (maybe the one motor is trying to retract the roof and that is why it is so hard to pull it up).
|
Originally Posted by Icemark
(Post 7427322)
Yeah, that would be my next step... going to the motors, disconnecting them and seeing if I can pop up the roof (maybe the one motor is trying to retract the roof and that is why it is so hard to pull it up).
I verified that if you move the switch to close, 12 V is applied to the G/W line at the left hand motor. So... Possible CPU problem? That would explain the intermittent nature of the problem up till now... Is the CPU part of that LH motor? If so I will remove it, take it to work, and reflow the solder work. |
Looks like the CPU is part of the RH motor. I give for the evening. Least I know the switch works!
|
Originally Posted by J-Rat
(Post 7427613)
Looks like the CPU is part of the RH motor. I give for the evening. Least I know the switch works!
|
Originally Posted by Icemark
(Post 7427094)
Yeah, just pull
http://www.cabrio7.org/rx7man1.html J-Rat, click on "If the top cannot be raised using the switch" and follow the instructions. |
Originally Posted by NZConvertible
(Post 7428122)
You've missed out an important step, as explained in the owners manual. ;)
http://www.cabrio7.org/rx7man1.html J-Rat, click on "If the top cannot be raised using the switch" and follow the instructions. |
Originally Posted by NZConvertible
(Post 7428122)
You've missed out an important step, as explained in the owners manual. ;)
http://www.cabrio7.org/rx7man1.html J-Rat, click on "If the top cannot be raised using the switch" and follow the instructions. Thank you!!!!!! |
Sorry to hijack, but verts are equipped with roll bars?
|
Originally Posted by NZConvertible
(Post 7428122)
You've missed out an important step, as explained in the owners manual. ;)
http://www.cabrio7.org/rx7man1.html J-Rat, click on "If the top cannot be raised using the switch" and follow the instructions. |
Okay, top is up. When I go to the down position, the motors work (beeps and everything). When I go to the UP position, I get nothing..
|
Bad limit switch, left hand motor!!!
HELLS YEAH!!!! W00T!!!!! |
Thanks for all the help everyone!!
|
All times are GMT -5. The time now is 06:43 PM. |
© 2024 MH Sub I, LLC dba Internet Brands