Coked Engine?
#1
My **** keeps breaking.
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Columbia, Maryland
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
Coked Engine?
Hi guys -
Recently picked up a very nice S4 NA for under 500 bucks. Runs well, aside from the the creeping overheating. Also kind of weird how the blower only blows cold/room temp air, even when it's on full hot.
What I did already was:
- Flush old coolant. It was brown. Gross.
- Add water and some peak flush stuff.
- Drove around for a few hours.
- Flushed again -- clear water was now brown. Still gross.
I've done this process several times, and every time it seems to get a bit better. But the problem, ultimately, still persists. Also want to note, I've never let it get higher than 3/4 of the way on the heat gauge and the coolant buzzer has never gone off.
So I guess the engine itself has some sort of residue or "coke" on it that is causing the engine to slowly overheat? Should I use a mixture of water and acid to remove whatever is in the engine?
Any advice would be helpful. Thanks!
Recently picked up a very nice S4 NA for under 500 bucks. Runs well, aside from the the creeping overheating. Also kind of weird how the blower only blows cold/room temp air, even when it's on full hot.
What I did already was:
- Flush old coolant. It was brown. Gross.
- Add water and some peak flush stuff.
- Drove around for a few hours.
- Flushed again -- clear water was now brown. Still gross.
I've done this process several times, and every time it seems to get a bit better. But the problem, ultimately, still persists. Also want to note, I've never let it get higher than 3/4 of the way on the heat gauge and the coolant buzzer has never gone off.
So I guess the engine itself has some sort of residue or "coke" on it that is causing the engine to slowly overheat? Should I use a mixture of water and acid to remove whatever is in the engine?
Any advice would be helpful. Thanks!
#2
Is it rust or one of the stop-leak addatives?
Also, use the block drain plug near the driver's side motor mount. You'll get more of the old fluid out than if you use the radiator drain plug. I'd just flush it normally without addatives, since I am unaware if how it may affect your coolant seals.
Replace your thermostat if you suspect it is gunked up and may help your overheating issue.
Your heater core is probably filled with that same stuff and preventing it from heating up all the way. It could also be the air mix motor or logicon not routing air over the heater core. Try flushing the heater core.
Also, use the block drain plug near the driver's side motor mount. You'll get more of the old fluid out than if you use the radiator drain plug. I'd just flush it normally without addatives, since I am unaware if how it may affect your coolant seals.
Replace your thermostat if you suspect it is gunked up and may help your overheating issue.
Your heater core is probably filled with that same stuff and preventing it from heating up all the way. It could also be the air mix motor or logicon not routing air over the heater core. Try flushing the heater core.
#4
Senior Member
iTrader: (1)
Join Date: Mar 2002
Location: Jefferson , Ga
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
Rx7 stock guage has three positions- cold/normal/fuked. Never let it go past half. I learned the hard way a decade back. On s5 don't even let it get to half. It sits a hair under. Send it to kevin landers and get it fixed.
Trending Topics
#8
Is the logicon working correctly? Listen to see if you hear a door move when switching from hot to cold.
Also when you drive it try to baby it around and see if it still overheats. I had a coolant hose that would only leak when put under pressure ie gassed it or reved real high (above 3+)
Also when you drive it try to baby it around and see if it still overheats. I had a coolant hose that would only leak when put under pressure ie gassed it or reved real high (above 3+)
#10
My **** keeps breaking.
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Columbia, Maryland
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
I've pretty much been babying it from the get-go because the clutch is completely shot. (I mean, seriously dead).
I pulled the thermostat tonight and it looked like this:
I can only imagine this gunk is all throughout the internals. Anything viable for removing it?
I pulled the thermostat tonight and it looked like this:
I can only imagine this gunk is all throughout the internals. Anything viable for removing it?
#13
Trunk Ornament
iTrader: (11)
You can rent what's called a "block tester" from any parts store. This won't work if you have exhaust leaks or do this in a garage, as the solution detects combustion gasses. You can test (properly, might I add) for blown coolant seals this way. Just leave the radiator cap off and use the sniffer to check for combustion gasses in the coolant. I'd do that before getting too far with all those flushes. Do change out that thermostat though. Mazda OEM, all the way. Bad things happen when you use any other brand... I've had my own experience with that.
#14
talking head
fit the correct s4 thermostat and bleed the radiator from the screw on side of top hose spout
a bad thermostat not only does not open fully
,, it recirculates the hot water for another lap ,, as the bottom of the thermostat is a bypass hole plug
make sure the pressure relief cap is on the point that has the overflow hose to the bottle
the point is either on the thermostat neck , on top of the radiator ( if late rad )
or remote in front of the rad ( if very early rad )
as for the heater,, the control unit , motor , or thermostat controller maybe faulty
if you cant work it out then you can flip it manually
if you stick your head under the dash you can flip the linkage off the side of the valve and operate the valve manually to full open or full shut position
a bad thermostat not only does not open fully
,, it recirculates the hot water for another lap ,, as the bottom of the thermostat is a bypass hole plug
make sure the pressure relief cap is on the point that has the overflow hose to the bottle
the point is either on the thermostat neck , on top of the radiator ( if late rad )
or remote in front of the rad ( if very early rad )
as for the heater,, the control unit , motor , or thermostat controller maybe faulty
if you cant work it out then you can flip it manually
if you stick your head under the dash you can flip the linkage off the side of the valve and operate the valve manually to full open or full shut position
#15
Rotary Freak
iTrader: (16)
Agreed.
OP- Try some white vinegar on that thermostat. See if the scum comes off after it soaks for 24-48hrs.
If so, I'd flush your coolant system with white vinegar. Google it. It breaks down calcium deposits and cleans out the scum pretty well. I let it sit in radiators with calcium build up for 24hrs then flush it out both ways with a garden hose. Lots of deposits come out.
If you want help with a rebuild pm me, we're basically neighbors.
OP- Try some white vinegar on that thermostat. See if the scum comes off after it soaks for 24-48hrs.
If so, I'd flush your coolant system with white vinegar. Google it. It breaks down calcium deposits and cleans out the scum pretty well. I let it sit in radiators with calcium build up for 24hrs then flush it out both ways with a garden hose. Lots of deposits come out.
If you want help with a rebuild pm me, we're basically neighbors.
#16
My **** keeps breaking.
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Columbia, Maryland
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
OK - I'll pick up some vinegar on the way home from work.
The gasket was also pretty much destroyed. I picked up some high temp RTV to form a new one. How long should I wait for it to cure before driving? 24 hours?
The gasket was also pretty much destroyed. I picked up some high temp RTV to form a new one. How long should I wait for it to cure before driving? 24 hours?
#17
My **** keeps breaking.
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Columbia, Maryland
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
Replaced thermostat - flushed engine, runs like a dream...
Until I hit red lights. It takes a LONG time to heat up, but it gets hot if I sit still. Warm air comes out of the logicon now, and if I keep the car moving, it's bang on at 1/3 temp gauge.
So I'm thinking the clutch fan is shot? Any other ideas?
(When it warms up to 1/2, and I then start driving, the temp falls -- So the radiator and thermostat must be doing their jobs correctly)
Edit: Also, replaced thermostat with an OEM one, not a stant.
Until I hit red lights. It takes a LONG time to heat up, but it gets hot if I sit still. Warm air comes out of the logicon now, and if I keep the car moving, it's bang on at 1/3 temp gauge.
So I'm thinking the clutch fan is shot? Any other ideas?
(When it warms up to 1/2, and I then start driving, the temp falls -- So the radiator and thermostat must be doing their jobs correctly)
Edit: Also, replaced thermostat with an OEM one, not a stant.
#20
Sharp Claws
iTrader: (30)
nothing is keeping him from coming back that i know of.
just because someone opts not to or doesn't care to defend themself doesn't mean that it can't be brought up, that's just a rediculous point of view... should i hypothetically go and rip off a bunch of people and then leave the forum? i guess it shouldn't be discussed afterwards because i don't come back to defend myself? that's straight up ignorant.
who's to say he won't try and come back and rip on me? then again i'll simply post pictures of that FD engine with welded exhaust port sleeves, i simply don't know how he can defend that one. chunks of metal going through the turbos generally isn't good for them. it was lazy and cheap, too cheap.
just because someone opts not to or doesn't care to defend themself doesn't mean that it can't be brought up, that's just a rediculous point of view... should i hypothetically go and rip off a bunch of people and then leave the forum? i guess it shouldn't be discussed afterwards because i don't come back to defend myself? that's straight up ignorant.
who's to say he won't try and come back and rip on me? then again i'll simply post pictures of that FD engine with welded exhaust port sleeves, i simply don't know how he can defend that one. chunks of metal going through the turbos generally isn't good for them. it was lazy and cheap, too cheap.
Last edited by RotaryEvolution; 10-03-11 at 05:11 PM.
#21
Trunk Ornament
iTrader: (11)
As a side note, the radiator (in my opinion) for the Rx7 was SEVERELY under developed. The engineers that designed this car did not (once again, in my opinion) give it a nearly large enough radiator. People who live in the south routinely have issues with this (such as myself). A larger radiator and a properly working cooling fan is what should be in any Rx7 owner's near future, if not already done.
#22
My **** keeps breaking.
Thread Starter
iTrader: (2)
Join Date: Jul 2005
Location: Columbia, Maryland
Posts: 86
Likes: 0
Received 0 Likes
on
0 Posts
Do you have a fan and does it work? Fan shroud? Plastic under-tray?
As a side note, the radiator (in my opinion) for the Rx7 was SEVERELY under developed. The engineers that designed this car did not (once again, in my opinion) give it a nearly large enough radiator. People who live in the south routinely have issues with this (such as myself). A larger radiator and a properly working cooling fan is what should be in any Rx7 owner's near future, if not already done.
As a side note, the radiator (in my opinion) for the Rx7 was SEVERELY under developed. The engineers that designed this car did not (once again, in my opinion) give it a nearly large enough radiator. People who live in the south routinely have issues with this (such as myself). A larger radiator and a properly working cooling fan is what should be in any Rx7 owner's near future, if not already done.
I'm looking into an e-fan solution anyway.
#23
Trunk Ornament
iTrader: (11)
I used a Hayden 16" single speed fan. You can get one from any parts store. 2 speed is overrated.
This is how I made the fan shroud:
https://www.rx7club.com/2nd-gen-archive-72/diy-electric-fan-shroud-808292/
This is how I made the fan shroud:
https://www.rx7club.com/2nd-gen-archive-72/diy-electric-fan-shroud-808292/
#24
When I first got my koyo rad I drive around for a week w/ no fan at all! As long as I wasnt sitting still temp was between 1/4 (proper stock position) and 1/3 ....and that was on a T2.
Certainly sounds like a fan issue, if you are looking into efans check out the mercury villager/nissan quest fan. Its got a great shroud, draws less amps than the taurus (although I would upgrade from the shitty s4 alt before any efan swap) and blows like a tornado even on the low speed (like -10° in 10 sec)
Certainly sounds like a fan issue, if you are looking into efans check out the mercury villager/nissan quest fan. Its got a great shroud, draws less amps than the taurus (although I would upgrade from the shitty s4 alt before any efan swap) and blows like a tornado even on the low speed (like -10° in 10 sec)
#25
This sh*t burns oil!
iTrader: (7)
As a side note, the radiator (in my opinion) for the Rx7 was SEVERELY under developed. The engineers that designed this car did not (once again, in my opinion) give it a nearly large enough radiator. People who live in the south routinely have issues with this (such as myself). A larger radiator and a properly working cooling fan is what should be in any Rx7 owner's near future, if not already done.