Car builds boost but goes nowhere, HELP ME PLEASE!!!
#27
What you lookin' at?
![](https://www.rx7club.com/images/misc/15_year_icon.png)
Join Date: Aug 2002
Location: Kansas City
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Well i blew a small vac line off my car the other night and I tried getting in boost and it would hesitate while getting into boost and it would kind of idle a little funny by either dropping down lower than usual (like its about to die) or it would go up higher. I found the line and put it back on and it would run just fine.
#28
Rotary Freak
![](https://www.rx7club.com/images/misc/10_year_icon.png)
iTrader: (1)
Join Date: Nov 2002
Location: Glyndon MN
Posts: 1,660
Likes: 0
Received 0 Likes
on
0 Posts
Yes my throttle plates did the same thing, the outboard ones were not opening. I then wired them open until I had time to do the TB mod and man it made a hell of a differance. Just wire those outboard plates open and you should see a huge gain.
#29
Powered By Trochoids
![](https://www.rx7club.com/images/misc/05_year_icon.png)
Thread Starter
Join Date: Oct 2004
Location: Philly | PA
Posts: 1,457
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SpeedyRotary
Well i blew a small vac line off my car the other night and I tried getting in boost and it would hesitate while getting into boost and it would kind of idle a little funny by either dropping down lower than usual (like its about to die) or it would go up higher. I found the line and put it back on and it would run just fine.
#30
Powered By Trochoids
![](https://www.rx7club.com/images/misc/05_year_icon.png)
Thread Starter
Join Date: Oct 2004
Location: Philly | PA
Posts: 1,457
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by usmcjsy
Yes my throttle plates did the same thing, the outboard ones were not opening. I then wired them open until I had time to do the TB mod and man it made a hell of a differance. Just wire those outboard plates open and you should see a huge gain.
#31
What you lookin' at?
![](https://www.rx7club.com/images/misc/15_year_icon.png)
Join Date: Aug 2002
Location: Kansas City
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Mindspin311
Sounds like my problem, but the nipple that the vac line is on broke off, so I gotta figure out how to re attach it.
JB weld the nipple?
![Big Grin](https://www.rx7club.com/images/smilies/biggrin.gif)
#33
Powered By Trochoids
![](https://www.rx7club.com/images/misc/05_year_icon.png)
Thread Starter
Join Date: Oct 2004
Location: Philly | PA
Posts: 1,457
Likes: 0
Received 0 Likes
on
0 Posts
I dont have a picture at the moment as I left my camera at school, hopefully once a local FC friend of mine gets off work at 9pm, I can head over to his house and snag a picture of it.
Oh, and how are our set-ups similar?
Oh, and how are our set-ups similar?
#34
What you lookin' at?
![](https://www.rx7club.com/images/misc/15_year_icon.png)
Join Date: Aug 2002
Location: Kansas City
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
S-AFC, bnr stage 4, 4x720cc injectors,walbro 255, FCD i think those are the same but i've also got the apexi dual n1's with no cats from a 2.5 in dp to mid pipe, bonez intake with a 2.5" TID with 3mm apex seals on a streetport.
pic:
pic:
![](http://mpg.cc/blind420/myae_large.jpg)
Last edited by SpeedyRotary; 05-19-05 at 05:44 PM.
Thread
Thread Starter
Forum
Replies
Last Post
82streetracer
Haltech Forum
11
03-11-19 05:34 PM
smikels
2nd Generation Specific (1986-1992)
3
08-18-15 01:26 PM