Anyone with a HKS F-Con. I need your help!
04-21-05, 07:04 PM
#1
Anyone with a HKS F-Con. I need your help!
My F-Con came to me (used) with the pressure snesor wires pulled out.
I'm guessing that they go into the plug that goes into the actual F-Con?
Where at, I have the little pins, and just don't know which pinouts to put them in.
A picture would be even better, since I don't want to screw something like this up. As it would be VERY bad.
Any help is appreciated
And also on the little "****" inside, is 5 stock, and lower than 5 leaner and higher richer?
Sorry but I got no instructions.
Thanks,
Ben Martin
I'm guessing that they go into the plug that goes into the actual F-Con?
Where at, I have the little pins, and just don't know which pinouts to put them in.
A picture would be even better, since I don't want to screw something like this up. As it would be VERY bad.
Any help is appreciated
And also on the little "****" inside, is 5 stock, and lower than 5 leaner and higher richer?
Sorry but I got no instructions.
Thanks,
Ben Martin
04-21-05, 08:19 PM
#2
Junior Member
Join Date: Nov 2004
Location: Las Vegas
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
My F Con had a separate connector specifically for the pressure sensor. I dont know too much about it cuz I never actually used it... my car has never run well enough to play with it.
04-21-05, 10:01 PM
#4
infini guru
Join Date: Nov 2001
Location: Sunnyvale, CA
Posts: 1,183
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Node
My F-Con came to me (used) with the pressure snesor wires pulled out.
I'm guessing that they go into the plug that goes into the actual F-Con?
Where at, I have the little pins, and just don't know which pinouts to put them in.
A picture would be even better, since I don't want to screw something like this up. As it would be VERY bad.
Any help is appreciated
And also on the little "****" inside, is 5 stock, and lower than 5 leaner and higher richer?
Sorry but I got no instructions.
Thanks,
Ben Martin
I'm guessing that they go into the plug that goes into the actual F-Con?
Where at, I have the little pins, and just don't know which pinouts to put them in.
A picture would be even better, since I don't want to screw something like this up. As it would be VERY bad.
Any help is appreciated
And also on the little "****" inside, is 5 stock, and lower than 5 leaner and higher richer?
Sorry but I got no instructions.
Thanks,
Ben Martin
Steve
04-22-05, 02:24 AM
#7
i have mine set at 7, a littler richer than needed but better then running lean. the pressure sensor should have a wiring harness that attaches to the main harness. if you send pics to tonypvu@gmail.com, ill try and see whats wrong and help you out.
Trending Topics
04-22-05, 04:10 AM
#8
uhm, so is 5 stock?
my digicam doesnt work, so ill try to explain as best as i can.
my pressure sensor has a big round plug about 6" from the pressure sensor, and then i have the other side of that plug with about 3' of wiring. and then that is cut, then i have another 2' of wiring w/ no electrical tape type wrapping and its a blue wire, a green wire and a yellow wire that have 3 female electrical connectors. i even checked and they fit on the male pins that are in the back of the f-con.
im fairly positive that those pins are supposed to be in the plug that goes into the back of my f-con. ill try to get my camera working or borrow someones.
my digicam doesnt work, so ill try to explain as best as i can.
my pressure sensor has a big round plug about 6" from the pressure sensor, and then i have the other side of that plug with about 3' of wiring. and then that is cut, then i have another 2' of wiring w/ no electrical tape type wrapping and its a blue wire, a green wire and a yellow wire that have 3 female electrical connectors. i even checked and they fit on the male pins that are in the back of the f-con.
im fairly positive that those pins are supposed to be in the plug that goes into the back of my f-con. ill try to get my camera working or borrow someones.