86 rx7 troubles, apex seals??
#1
1.3 liter piston eater
Thread Starter
iTrader: (1)
Join Date: Jan 2009
Location: washington
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
86 rx7 troubles, apex seals??
so i just picked up an extremely clean 86 fc for 500 bucks and it has 57,xxx on it. but according to the old owner, it has a blown apex seal. now this is kinda hard to believe because when the car is on, it sounds really smooth and revs up normally and it doesn't stumble or have and weird smoke coming out of it. but on the other hand the car is really lacking power and will not idle on its own and has a major oil leak from what i think is one of the oil cooler lines.
i was jut curious if anybody has any good ways of figuring out if it actually has a blown seal. also the old owner says that the motor was rebuilt by Atkins about 7 years ago.
i was jut curious if anybody has any good ways of figuring out if it actually has a blown seal. also the old owner says that the motor was rebuilt by Atkins about 7 years ago.
#2
Rotary Enthusiast
iTrader: (17)
Join Date: Dec 2007
Location: Texas
Posts: 785
Likes: 0
Received 0 Likes
on
0 Posts
take out the trailing plugs and the egi fuse and try to crank the car. If all the pulses are there with no gaps in between all of your apex seals are intact. As for the side and corner seals someone else has to chime in.
#7
Rotary Enthusiast
iTrader: (17)
Join Date: Dec 2007
Location: Texas
Posts: 785
Likes: 0
Received 0 Likes
on
0 Posts
Did you check it already? I would do that before I start trying to buy another motor. It may be a really easy fix. A gave a friend of mine a perfectly good motor and put it in the car for him. Then 2 weeks later he put atf in it to try and "raise compression", then he complained about not having power. It idled perfect and sounded good but it could outrun a school bus pulling a motor home. Well I took a look at it and the only problem was he put the spark plug wires on wrong . Just make sure you test things out before you jump to conclusions. It may be something really really simple . Good Luck!
Trending Topics
#10
1.3 liter piston eater
Thread Starter
iTrader: (1)
Join Date: Jan 2009
Location: washington
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
this is literally exactly how my rx7 runs. im going to go ahead an assume its a chipped seal
<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/CmqqMkk9E7E&hl=en_US&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/CmqqMkk9E7E&hl=en_US&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/CmqqMkk9E7E&hl=en_US&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/CmqqMkk9E7E&hl=en_US&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
#12
Rotary Enthusiast
iTrader: (17)
Join Date: Dec 2007
Location: Texas
Posts: 785
Likes: 0
Received 0 Likes
on
0 Posts
<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/7LWqCLxcNXc&hl=en_US&fs=1&rel=0"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/7LWqCLxcNXc&hl=en_US&fs=1&rel=0" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
It should sound consistent like this, should be much faster in your case. Remember to pull the egi fuse, so no spark and it wont start up on you.
It should sound consistent like this, should be much faster in your case. Remember to pull the egi fuse, so no spark and it wont start up on you.
#14
Senior Member
Join Date: Aug 2009
Location: Los Angeles
Posts: 479
Likes: 0
Received 0 Likes
on
0 Posts
Before you buy a motor, have you checked:
Trouble codes?
Closed loop operation?
Proper operation of the double throttle diaphragm?
Air cleaner?
AFM?
Air temp sensor?
Baro pressure sensor?
TPS?
Water thermo sensor?
BAC?
It almost sounds like a connector fell off a sensor while he was driving...
Trouble codes?
Closed loop operation?
Proper operation of the double throttle diaphragm?
Air cleaner?
AFM?
Air temp sensor?
Baro pressure sensor?
TPS?
Water thermo sensor?
BAC?
It almost sounds like a connector fell off a sensor while he was driving...
#16
1.3 liter piston eater
Thread Starter
iTrader: (1)
Join Date: Jan 2009
Location: washington
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
ok so i just did that 3 woosh test and in my opinion it passed with flying colors. every woosh sounded really healthy and almost made a whistle sound. now the question is, can you have a chipped apex seal and still pass the woosh test? is there any other seals that could cause my problem and still allow it to pass the woosh test?
#18
313 whp 247 wtq 8D
iTrader: (2)
Join Date: Dec 2009
Location: in my car
Posts: 570
Likes: 0
Received 0 Likes
on
0 Posts
I lost an apex seal in my rear rotor and I had no clue. The car ran perfectly fine, didn't smoke, and still had plenty of power. Sometimes I would have hot start problems so I did a compression test and only had 70 psi so now the motors out and I definetly had a broken seal-
#19
1.3 liter piston eater
Thread Starter
iTrader: (1)
Join Date: Jan 2009
Location: washington
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
well i don't have a rotary compression tester. and plus idk what psi it is supposed to be at. and if i use a piston compression tester, whats a good psi it should be at? because i know a rotary will register super low on a piston compression tester
#20
S5 T2
iTrader: (6)
I was unaware they made rotary specific compression testers. Air pressure is air pressure, no matter what's creating it. Do a search on compression numbers, shouldn't be difficult to find. Even if you don't know the numbers, you'll know if you have poor compression when the readings don't match.
#21
313 whp 247 wtq 8D
iTrader: (2)
Join Date: Dec 2009
Location: in my car
Posts: 570
Likes: 0
Received 0 Likes
on
0 Posts
I'm pretty sure you can buy any old compression tester at sears and it will work fine.(thats what i did) Anything over 100psi is great and over 90psi is good and i think 80psi is about the lowest you want to see.
#22
1.3 liter piston eater
Thread Starter
iTrader: (1)
Join Date: Jan 2009
Location: washington
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
OK so i compression tested it and the front rotor is just about 100 and the rear rotor barely even registers on the gauge. the first number on the gauge is 25 and it doesn't even make it to that
so my next question now is if im getting that low of compression on the rear rotor, doesn't that mean all 3 rear rotor apex seals are bad? like i said, when i did the whoosh test, it sounded really healthy
so my next question now is if im getting that low of compression on the rear rotor, doesn't that mean all 3 rear rotor apex seals are bad? like i said, when i did the whoosh test, it sounded really healthy
#23
Disco Biscuit
iTrader: (9)
You only need 2 bad seals on a rotor to create that condition (it's a triangle). One seal probably broke, and then damaged the next as it was tumbling the broke one around. OR You might not have had the tester screwed in far enough to make a good seal?
You need a rebuild/replacement. You might consider doing a turbo swap to it, while you are at it.
You need a rebuild/replacement. You might consider doing a turbo swap to it, while you are at it.
#25
1.3 liter piston eater
Thread Starter
iTrader: (1)
Join Date: Jan 2009
Location: washington
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
ok so ive decided to rebuild my motor. i wanna get my rebuild kit from atkins, should i get the overhaul kit or the rotor kit? the overhaul one costs 300 and the rotor one costs 700. but the overhaul one comes with all the same stuff as the rotor kit and it even comes with a gasket kit, which the rotor kit does not come with.