11k miles,streetport &3mm seals
#1
11k miles,streetport &3mm seals
Well here i stand with a blown engine.
Had a street ported (mild) 3mm seals from Jeffy @ Rotary Power done back in Jan this year now 11 000 miles later broken.Also did silicone vac lines stage 2 hybrid turbo,baided steel coller lines,new Fuel damp.,comp motor mounts,lightened steel flywheel,
Broken almost all side seals and 5/6 3mm apex seals.
bent rotors slots for 3mm seall so clearance is too big.
dented rotor on combustion face
History
In order
Run-in of engine was good 1000 miles and under 4k rpms no issues there.
Also notice Oil pressure was low, just above 30 @ above 3000rpm and below @ idle.
still had main CAT on and could only do 4.5# of boost
told Jeff and tried a Manual Boost Controller and still no effect.(4000 miles)
Changed out cat to Racing beats Presilincer (already had catback exhast)(6000 miles)
Boost now went to 14 #...... Car pulled really good.
Throwing flames.. 1 - 2 ft long.
Big back fires loud like gun shots,
really loud backfire and then idle was shitty ie car could idle @ about 400rpm-600rpm but stall after about 30-60 sec.(about 9000miles)
car still very drivable,8th June my b-day take a nice long drive 300miles @ night
in 4th go to 14# @ WOT and there was a bog in power ease off and then find power comes back. and every thing is fine
@ end of drive going home feel car is not performing well, listen to idle @ stop light and hear a constant klunk in tune with rotation on engine,only below 600rpm
have to nurse idle,
General NOTES..
I always let the car and turbo cool down. I have long down hill slop into apartment garage 150yards and idle in to parking bay and run for about 2mins.
Always tried to keep below 11# when driving normally and opening to almost WOT
if pushing then went to 14 # , 2 or 3 times a drive.
Bosch Oxygen sensor with Automere A/F R gauge always said rich when foot on accelerator never stoich,
Always filled up wil 91 Octane from Mobil or 76
Thanks fully the 3mm seals never crubled and damaged the rotor housings and the turbo..
I will now always support 3mm apex seals if you are as dumb as i am and even if you are not cause it will save your more of your motor in the long run if you mess and do not make the appropriate upgrades to support 14 # of boost
Had a street ported (mild) 3mm seals from Jeffy @ Rotary Power done back in Jan this year now 11 000 miles later broken.Also did silicone vac lines stage 2 hybrid turbo,baided steel coller lines,new Fuel damp.,comp motor mounts,lightened steel flywheel,
Broken almost all side seals and 5/6 3mm apex seals.
bent rotors slots for 3mm seall so clearance is too big.
dented rotor on combustion face
History
In order
Run-in of engine was good 1000 miles and under 4k rpms no issues there.
Also notice Oil pressure was low, just above 30 @ above 3000rpm and below @ idle.
still had main CAT on and could only do 4.5# of boost
told Jeff and tried a Manual Boost Controller and still no effect.(4000 miles)
Changed out cat to Racing beats Presilincer (already had catback exhast)(6000 miles)
Boost now went to 14 #...... Car pulled really good.
Throwing flames.. 1 - 2 ft long.
Big back fires loud like gun shots,
really loud backfire and then idle was shitty ie car could idle @ about 400rpm-600rpm but stall after about 30-60 sec.(about 9000miles)
car still very drivable,8th June my b-day take a nice long drive 300miles @ night
in 4th go to 14# @ WOT and there was a bog in power ease off and then find power comes back. and every thing is fine
@ end of drive going home feel car is not performing well, listen to idle @ stop light and hear a constant klunk in tune with rotation on engine,only below 600rpm
have to nurse idle,
General NOTES..
I always let the car and turbo cool down. I have long down hill slop into apartment garage 150yards and idle in to parking bay and run for about 2mins.
Always tried to keep below 11# when driving normally and opening to almost WOT
if pushing then went to 14 # , 2 or 3 times a drive.
Bosch Oxygen sensor with Automere A/F R gauge always said rich when foot on accelerator never stoich,
Always filled up wil 91 Octane from Mobil or 76
Thanks fully the 3mm seals never crubled and damaged the rotor housings and the turbo..
I will now always support 3mm apex seals if you are as dumb as i am and even if you are not cause it will save your more of your motor in the long run if you mess and do not make the appropriate upgrades to support 14 # of boost
Trending Topics
#13
Nothing to see here.
They are telling you that you were running too much boost without enough fuel and probably too high of an intake temp. I'm no expert but that seems like a very good combo for detonation.
#14
SOLD THE RX-7!
Join Date: Mar 2001
Location: Vancouver, BC, Canada
Posts: 7,451
Likes: 0
Received 0 Likes
on
0 Posts
if you build another engine you're just gona blow that up too... with stock injectors and stock IC, 14psi is way too much for a stock engine and stock turbo
now you have a ported engine and bigger turbo at 14psi. which equals up towards 20psi on the stock turbo.
your current system is good for around 8psi. maybe 10 if you're lucky
you need four 720cc injectors and a S-afc. and to have it dyno tuned with a wide band o2. as well as a FMIC.
now you have a ported engine and bigger turbo at 14psi. which equals up towards 20psi on the stock turbo.
your current system is good for around 8psi. maybe 10 if you're lucky
you need four 720cc injectors and a S-afc. and to have it dyno tuned with a wide band o2. as well as a FMIC.
#15
Super Raterhater
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,630
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by Scott 89t2
if you build another engine you're just gona blow that up too... with stock injectors and stock IC, 14psi is way too much for a stock engine and stock turbo
now you have a ported engine and bigger turbo at 14psi. which equals up towards 20psi on the stock turbo.
your current system is good for around 8psi. maybe 10 if you're lucky
you need four 720cc injectors and a S-afc. and to have it dyno tuned with a wide band o2. as well as a FMIC.
if you build another engine you're just gona blow that up too... with stock injectors and stock IC, 14psi is way too much for a stock engine and stock turbo
now you have a ported engine and bigger turbo at 14psi. which equals up towards 20psi on the stock turbo.
your current system is good for around 8psi. maybe 10 if you're lucky
you need four 720cc injectors and a S-afc. and to have it dyno tuned with a wide band o2. as well as a FMIC.
#18
Senior Member
iTrader: (5)
Join Date: Jan 2002
Location: Texas
Posts: 650
Likes: 0
Received 0 Likes
on
0 Posts
Damn, that's what my friend did too to his motor. 2, didn't learn his lesson. We rebuild it again and he has a haltech now, and he has over 10k and still running strong. Be smart and get some fuel mods.*-
#21
Daily Domestic Killer
Join Date: Mar 2001
Location: San Antonio, Tx, USA
Posts: 2,425
Likes: 0
Received 0 Likes
on
0 Posts
Also notice Oil pressure was low, just above 30 @ above 3000rpm and below @ idle
#23
SOLD THE RX-7!
Join Date: Mar 2001
Location: Vancouver, BC, Canada
Posts: 7,451
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by mr_vaughn
so here is what happening
ported waste gate
Apexi AVC-R
Greddy FMIC
new rotors
and still 3mm seals
so here is what happening
ported waste gate
Apexi AVC-R
Greddy FMIC
new rotors
and still 3mm seals