what do ya think?
#27
you know you want this
Thread Starter
Originally Posted by rookie117
hey! im working on putting a setup like yours in my car... ive got a 13b 4-port, bridgeported, holley 650, msd ignition, header to a 3' pipe, and other stuff. tell me more about how it runs!!! i cant wait to get mine done and running. post a pic of your engine bay.
-i'll post pics of the engine bay next time im over my buddies house (who so kindly gave up his heated garage to my car)
let me know if you want to know any more.
#28
Rotary Enthusiast
Join Date: Jun 2003
Location: Calgary; AB
Posts: 1,288
Likes: 0
Received 0 Likes
on
0 Posts
anything at this point in time is better than the blue you got on that car now...I would suggest candy apple red with metal flec to give it a wicked shimmer when the sun hits it...or this really wicked green that I want to paint my car but can't tell anyone till I got it painted...its my green...
#30
you know you want this
Thread Starter
im leaning heavily towards a deep candy blue with moderate flake. i want at least some blue to go with the interior. should set the car off nice, eh?
#32
Senior Member
iTrader: (1)
Originally Posted by old_skool
it idles like a beast, kinda rough at about 1500 RPM. moderate power till about 4000, but above that, all i can say is HOLD ON! (make sure the carb is jetted to the weather, or it will run like C-R-A-P) she also takes about 15 minutes to get up to temp at 60F, but that may be due to the massive oil cooler. i also put 12 oz of oil per 10 gallons of gas into the tank. i also have 3.90 gears in the rear, to hold out the gears longer with the spray at the track. all this and i still get 10 MPG city. i like this setup...ALOT!
-i'll post pics of the engine bay next time im over my buddies house (who so kindly gave up his heated garage to my car)
let me know if you want to know any more.
-i'll post pics of the engine bay next time im over my buddies house (who so kindly gave up his heated garage to my car)
let me know if you want to know any more.
im soo excited!!!! ive been working on my car since summer, and im soo close to being ready to putting the engine in! probably within the next few weeks!! the more i hear the more i get excited! im not doing nos so im lookin at a gsl-se rear end. i beleive its 4:20 gear ratio. (that or 4:10) either way, do you know what kind of 1/4 mile times you would run without the nos? im looking for low 13s at least.
erick
#33
you know you want this
Thread Starter
Originally Posted by DIETER SCHELLE
NICE,NICE, I LIKE IT!!!!!!!
Some questions?? What apex seals,full or half brige,SPRAYBAR or PORT INJECTION?
jet sizes if possible?
NICE RIDE
Some questions?? What apex seals,full or half brige,SPRAYBAR or PORT INJECTION?
jet sizes if possible?
NICE RIDE
#34
you know you want this
Thread Starter
Originally Posted by rookie117
im soo excited!!!! ive been working on my car since summer, and im soo close to being ready to putting the engine in! probably within the next few weeks!! the more i hear the more i get excited! im not doing nos so im lookin at a gsl-se rear end. i beleive its 4:20 gear ratio. (that or 4:10) either way, do you know what kind of 1/4 mile times you would run without the nos? im looking for low 13s at least.
erick
erick
#35
No not carb jet sizes,nos sizes if possible?I am almost done with my weber set up,just need some spares for nos system and then want to test it!My sizes is 1mm for feul and the nos side is0.85mm,but feul pressure is set at 1bar(14psi).I am running a port injection system!
#36
you know you want this
Thread Starter
Originally Posted by DIETER SCHELLE
No not carb jet sizes,nos sizes if possible?I am almost done with my weber set up,just need some spares for nos system and then want to test it!My sizes is 1mm for feul and the nos side is0.85mm,but feul pressure is set at 1bar(14psi).I am running a port injection system!
#38
you know you want this
Thread Starter
Originally Posted by FirebirdSlayer666
Nice 7. Did you smoke the taillights out more or did you get it that way? I want my taillights like those. Sweet
#39
you know you want this
Thread Starter
Originally Posted by DIETER SCHELLE
No not carb jet sizes,nos sizes if possible?I am almost done with my weber set up,just need some spares for nos system and then want to test it!My sizes is 1mm for feul and the nos side is0.85mm,but feul pressure is set at 1bar(14psi).I am running a port injection system!
#41
you know you want this
Thread Starter
Originally Posted by FirebirdSlayer666
Sweet. Not to sound demanding but could I see how they look lit up at night? GREATLY APPRECIATED
#44
you know you want this
Thread Starter
Originally Posted by FirebirdSlayer666
Sweet thanks. Would you happen to know where I could get taillight paint? I didn't see it online for 8$. It was like $30
#45
you know you want this
Thread Starter
Originally Posted by DIETER SCHELLE
ITs a 75-80hp shot,why disconnect the trailing side?.Timing now on engine is 20-22 deg leading and 12-13deg trail!