loki86golf

as i have no pics i will discribe.

looking at the engine cavity, there is a clack canister. it has a trottle cable coming from it and i dont know what it is.

looking to strip whatever i can before the carb gets put back in. also would like a thread post with pictures as to what i can remove emissions wise(yes yes i know).
im in dallas, tx and we have emissions but they dont check exhaust quailty or anything they just check to see if the car has a cat. and that it doesnt have any codes messed up(not that i need to worry about that)

please know i am not a noob but there are somethings i just dont know. i moved here from colorado and in the country there in co there arent any emissions to worry about.


thanks in advance.

acekid7

iTrader: (1)

is it on the passenger side of the car because if it is i think u are talking about the cruse control. It works off of vacuum so make sure u plug up the other end.

mazdaverx713b

iTrader: (91)

what year and trim level?

loki86golf

1983 gsl. yes the passenger. it has a throttle cable coming from it. also on the driver side there is another item i havent seen before its mounted to the strut tower wall. it also has a throttle cable

jdmminot

iTrader: (6)

The passenger side is the cruise control module, the one on the drivers strut tower is the hot start assist system. Basically it pumps the gas once or twice as your starting the vehicle. Both of these systems can be ditched very easily, but with the hsa you must remove/wire up the arm on the throttle linkage that the cable originally attached to.

https://www.rx7club.com/1st-generation-specific-1979-1985-18/hot-start-assist-bracket-removal-nikki-carb-943470/

Kentetsu

This might interest you:

https://www.rx7club.com/1st-gen-archive-71/other-finally-some-pics-441703/





.

loki86golf

okay so what is this lmao says : sub zero antifreeze:

RX-7 Chris

iTrader: (19)

it's the sub-zero tank. It sprays coolant into the tank when you atart it and it's below zero. It doesn't really do anything and can be removed.

Kentetsu

That link I posted above will detail a great deal of what can be removed, and what can be relocated. Check it out if you haven't...

loki86golf

okay next question. i need a diagram on the vacuum nest on top of the engine.... dont send me to the stupid arguement on the other post.... its useless..... i am taking the a/c off and the air pump is gone i need to know what color noids. need to be left alone. my other car didnt have all the crap that a sports car doesnt need like this one. dont need a explanation of how the nest works just color codes please

j9fd3s

iTrader: (3)

i believe that is on the sticker on the underside of the hood

deadphoenix52

iTrader: (2)

you need a haynes manual or to download the service manuals

and 2: texas emmissions testing is required for cars 2-24 years old. so your car will not be tested at all. they wont even check to see if it has a cat. i know this because my car does not have a cat and passed inspection

Hec's 79 gs

^^ my 85 SE did not have to pass emissions last year so 86 is this year and that was in Houston.

dankekong

iTrader: (2)

go to http://maz_tutorials.ten15.net/Tutorial_1.pdf and this will detail the entire emissions removal process...leaving what you do and dont need.

if youre removing the a/c...then you dont need that white solenoid which is in this tutorial. it will tell you though what is what.

good luck!

loki86golf

okay now i have a big issue....... i havent started anything off yet all i did was putmy freshly rebuilt carb back on and it still wont stay running. it has a new fuel filter new furl pump, checked all spark and it still good.....(trust my burnt hand) when i touched the coil by accident when the wire wasloose too checkk. but it wonnt stay running.took the fuel inlet hose off the carb and its pumping fuel but i can put my finger ofver the hose and stop the fuel is that right?????
also if i pump the pedal 20 or 30 times(figured out in anger) it will pump enough fuel into the carb to start. any help would be great.

any guys or girls around dallas let me know i could use some help.

jon

cshaw07

iTrader: (14)

who rebuilt the carb? did you pull out all the jets and air bleeds and clean them? also, did you burnish the corners of the needles before you installed them?

loki86golf

okay so was waiting on the carb and started messing with other things and got really into it.
then i get the carb back and put it on and now i find out that the front rotor lost all compression.
now i need an engine...... anyone know or have an 12a engine around dallas for sale
email me loki86golf@gmail.com just post the subject as rx7club