Sportmax 002 on FB
02-03-10, 09:28 AM
#59
Senior Member
iTrader: (1)
Join Date: Feb 2007
Location: Winnipeg
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
And some lowering springs. Holy wheel gap batman! How much room do you have to the inside spring? Could you get a shop to machine them down to change the offset? Would tuck them in a little nicer...
02-03-10, 04:19 PM
#62
has seen the light.
Join Date: Sep 2009
Location: Uniontown Ohio
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
02-08-10, 09:40 PM
#63
zoom zoom
iTrader: (5)
Join Date: Aug 2009
Location: Abq, NM
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
Not sure how you managed this..What brand tire were you using?
I picked up a set of these XXR's and am having a tough time getting them to fit. They are currently wrapped in Bridestone Re-01's and I had about half a steering wheel turn from center to left or right before they were hitting fender. I tried rolling the fenders and that helped a tad bit, but still couldn't turn. Most likely going to have to cut into the front fenders.
I picked up a set of these XXR's and am having a tough time getting them to fit. They are currently wrapped in Bridestone Re-01's and I had about half a steering wheel turn from center to left or right before they were hitting fender. I tried rolling the fenders and that helped a tad bit, but still couldn't turn. Most likely going to have to cut into the front fenders.
02-08-10, 10:09 PM
#65
BUY MY PARTS!!!
iTrader: (5)
Join Date: Nov 2004
Location: Blacksburg, VA
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
i think they are 225/45.15 Hankook RS-2.
I have rolled my fenders, and have Re-Speed Coilovers. Running -.4 deg neg front camber.
These would fit with the factory suspension, but it rubs every time I turned.
I have rolled my fenders, and have Re-Speed Coilovers. Running -.4 deg neg front camber.
These would fit with the factory suspension, but it rubs every time I turned.
02-11-10, 11:18 PM
#66
has seen the light.
Join Date: Sep 2009
Location: Uniontown Ohio
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
02-12-10, 07:36 PM
#67
BUY MY PARTS!!!
iTrader: (5)
Join Date: Nov 2004
Location: Blacksburg, VA
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
I rolled my fenders pretty tight, and my Spring Rates are 350/175. Camber didnt matter, but I dont run fender liners either.
I dont rub AT ALL. and this is an Auto-x car. must be the stiff springs saving me!
I dont rub AT ALL. and this is an Auto-x car. must be the stiff springs saving me!
03-28-10, 11:14 PM
#68
Rotary Powered Boobies
iTrader: (1)
Join Date: Oct 2001
Location: Miami Beach
Posts: 2,530
Likes: 0
Received 0 Likes
on
0 Posts
I just bought a 1990 Turbo Miata and was thinking about getting these. They 16x8 look sweet on this Rotary miata.
http://speedhunters.com/archive/2009...6ce-in-bc.aspx
If I decide to wait and spend a little more money, I might get these instead.
http://www.modbargains.com/_e/Miro_W...P_1_Wheels.htm
or these ESM wheels
http://www.esmwheels.com/main/produc...products_id=48
Not sure if they will fit First gens, but they would look nice.
http://speedhunters.com/archive/2009...6ce-in-bc.aspx
If I decide to wait and spend a little more money, I might get these instead.
http://www.modbargains.com/_e/Miro_W...P_1_Wheels.htm
or these ESM wheels
http://www.esmwheels.com/main/produc...products_id=48
Not sure if they will fit First gens, but they would look nice.
Thread
Thread Starter
Forum
Replies
Last Post
Caifanesrock
Suspension/Wheels/Tires/Brakes
7
02-15-08 05:27 PM
84FBturbo
Suspension/Wheels/Tires/Brakes
2
04-07-07 11:18 PM
