Rear seats?
#26
Junior Member
Originally Posted by rotarydude
And the Aussie seats should be the same as the ones i posted a pic of above
#27
Senior Member
iTrader: (2)
Luuuc,
I hope you don't drive the Fb in Winnipeg winters!
Probably the only reasonable solution to getting rear sets is to look out for Fc seats for sale in your color. Check out my thread for my install:
https://www.rx7club.com/1st-generation-specific-1979-1985-18/fc-rear-seat-install-misc-12a-turbo-fb-pics-581137/
I hope you don't drive the Fb in Winnipeg winters!
Probably the only reasonable solution to getting rear sets is to look out for Fc seats for sale in your color. Check out my thread for my install:
https://www.rx7club.com/1st-generation-specific-1979-1985-18/fc-rear-seat-install-misc-12a-turbo-fb-pics-581137/
#29
Back in the saddle again
iTrader: (2)
Originally Posted by jim_chung
Luuuc,
I hope you don't drive the Fb in Winnipeg winters!
Probably the only reasonable solution to getting rear sets is to look out for Fc seats for sale in your color. Check out my thread for my install:
https://www.rx7club.com/showthread.php?t=581137
I hope you don't drive the Fb in Winnipeg winters!
Probably the only reasonable solution to getting rear sets is to look out for Fc seats for sale in your color. Check out my thread for my install:
https://www.rx7club.com/showthread.php?t=581137
Very Nice instal and you know that the pattern matching FC seats will bolt in with very few modifications as well, I know your seats look great but just in case you are wondering I have done that to install T2 seats in an FB
#30
voo doo witchdoctor
Join Date: Aug 2005
Location: Texarkana, Arkansas
Posts: 365
Likes: 0
Received 0 Likes
on
0 Posts
i saw a thread awhile back where some dood put the rear seats out of a porche 924 in his rx7. i dont feel like posting the link so have sum fun with that search button.
#31
Junior Member
Join Date: Aug 2006
Location: ogden, UT 84405
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
i dont get why everyone thinks the back seats are so small....i've got back seats in mine and i have at least 5 people in my car every day for the past month or so, i've even had up to 8 people in my rx7
#34
www.RPNW.org Member
Join Date: Jan 2004
Location: McMinnville, OR
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
How do you get the rear seat out?
There are two studs behind the seat, on the support braces under the seat. Once those are off the seat will hinge forward but I can't get it to come out. Is there a pin or something holding it in?
It looks like there is some under the uphostery but I don't want to cut it just to see how it removes.
Like this one:
There are two studs behind the seat, on the support braces under the seat. Once those are off the seat will hinge forward but I can't get it to come out. Is there a pin or something holding it in?
It looks like there is some under the uphostery but I don't want to cut it just to see how it removes.
Like this one:
#35
Originally Posted by rotarydude
And the Aussie seats should be the same as the ones i posted a pic of above
#36
Old Fart Young at Heart
iTrader: (6)
Assuming the 1st gen seats are built like the 2nd gen ones:
You need to remove the bottom of the seat before the back. The front of the bottom clips in. About 8-10" from each side, push down, back then pull up. The back of the bottom is held in a similiar manner, but it's been a while since I've taken one out. I don't remember how the bottom side of the back is held in. But, iirc, you should see that after the bottom is removed.
You need to remove the bottom of the seat before the back. The front of the bottom clips in. About 8-10" from each side, push down, back then pull up. The back of the bottom is held in a similiar manner, but it's been a while since I've taken one out. I don't remember how the bottom side of the back is held in. But, iirc, you should see that after the bottom is removed.